BIS Certification for Live Working Gloves of Insulating Material – IS 13774:2021
Introduction
Live working gloves are specialized electrical protective equipment designed to protect workers from electrical hazards while performing work on or near energized electrical systems. Because these gloves are used as a primary or important layer of electrical protection, their insulation performance, mechanical strength, dimensions, flexibility, resistance to environmental conditions and marking must be carefully controlled.
For Live Working Gloves of Insulating Material, the applicable Indian Standard is IS 13774:2021, which is aligned with IEC 60903:2014. BIS operates certification for this product under Scheme-I through Product Manual PM/IS 13774/IEC 60903/2/February 2022.
The current BIS Product Manual covers Insulating and Composite Gloves in Classes 00, 0, 1, 2, 3 and 4, with special categories A, H, Z, R, C and F, different sizes, standard lengths and lined/unlined constructions.
Qualitance India provides complete BIS Certification consultancy for Live Working Gloves of Insulating Material, including product assessment, classification and scope planning, grouping guidance, sample preparation, testing coordination, documentation, factory inspection preparation, BIS application filing, licence processing and post-licence compliance.
What is IS 13774:2021?
IS 13774:2021 is the Indian Standard for:
Live Working – Gloves of Insulating Material
The standard is aligned with IEC 60903:2014 and establishes requirements for gloves used for electrical protection during live working.
The BIS Product Manual identifies the product as:
IS 13774:2021 / IEC 60903:2014 – Live Working Gloves of Insulating Material.
The certification framework addresses important characteristics such as:
- Composition
- Dimensions
- Thickness
- Workmanship and finish
- Marking
- Packaging
- Instructions for use
- Tensile strength
- Elongation at break
- Puncture resistance
- Tension set
- Dielectric performance
- Ageing
- Low-temperature performance
- Flame retardancy
- Special chemical/environmental resistance
- Abrasion resistance
- Cutting resistance
- Tear resistance
Current BIS Certification Status
The current BIS Scheme-I page lists:
IS 13774:2021 – Live Working Gloves of Insulating Material
under the mandatory certification framework.
The current BIS Product Manual is:
PM/IS 13774/IEC 60903/2/February 2022
and it states that certification is operated under Scheme-I. The manual records nil amendments to the standard in that product manual.
Is BIS Certification Mandatory for Live Working Gloves?
Yes. IS 13774:2021 is included in the Electrical Accessories Quality Control Order framework.
The applicable QCO identifies IS 13774:2021 – Live Working Gloves of Insulating Material among the regulated electrical products and specifies the BIS certification framework.
The BIS Scheme-I listing also continues to include the product.
Manufacturers should always verify the latest applicable notification, amendments and exemptions before placing regulated products on the Indian market.
Product Classification Under IS 13774:2021
The BIS licence scope is detailed and should be planned carefully.
Type
The Product Manual identifies:
- Insulating
- Composite
Class
The following classes are covered:
- Class 00
- Class 0
- Class 1
- Class 2
- Class 3
- Class 4
The class is an important part of the electrical performance and licence scope.
Special Categories
The Product Manual identifies:
- A – Acid Resistance
- H – Oil Resistance
- Z – Ozone Resistance
- R – Acid, Oil & Ozone Resistance
- C – Extremely Low Temperature Resistance
- F – Leakage Current Resistance
Size
The current Product Manual lists sizes:
7, 7.5, 8, 8.5, 9, 9.5, 10, 10.5, 11, 11.5 and 12
and permits other sizes where agreed between manufacturer and client, subject to the applicable requirements.
Standard Length
The listed standard lengths are:
- 280 mm
- 360 mm
- 410 mm
- 460 mm
- 800 mm Long
Lining
The Product Manual distinguishes:
- Lined gloves
- Unlined gloves
Why BIS Certification is Important for Electrical Insulating Gloves
Electrical insulating gloves are safety-critical PPE. Their main purpose is to provide electrical insulation while also remaining mechanically suitable for practical use.
A compliant glove needs to maintain its protective characteristics during handling and under the environmental and mechanical conditions covered by the standard.
BIS certification therefore provides a structured framework for checking:
Electrical insulation
The dielectric tests are designed to evaluate the glove’s electrical performance.
Mechanical strength
Tensile strength, elongation, puncture, abrasion, cutting and tear resistance address the physical robustness of the glove.
Environmental resistance
Ageing, low-temperature and applicable special-category tests assess performance under specified conditions.
Workmanship
Dimensions, thickness, finish and construction are controlled.
Product identification
Marking, packaging and instructions help ensure that the certified product can be identified and correctly used.
BIS Sample Size for IS 13774:2021
The current Product Manual specifies:
15 pairs of gloves
Additional samples may also be drawn depending on the type of glove and the requirements of Annex C of IS 13774.
Correct sample planning is especially important because the required samples can vary depending on:
- Glove type
- Class
- Special category
- Length
- Lining
- Composite construction
BIS Grouping Guidelines for Live Working Gloves
Grouping is an important part of the certification process.
The Product Manual identifies the grouping parameters as:
- Type
- Class
- Special category
- Size
- Length
- Lined/unlined construction
Different Glove Types
Insulating and Composite gloves are treated as separate groups.
Lined and Unlined Gloves
Lined and unlined gloves are also treated as separate groups.
Special Categories
Each special category and each combination of categories is to be tested separately.
This is especially important when planning products with:
- Acid resistance
- Oil resistance
- Ozone resistance
- Combined acid/oil/ozone resistance
- Extremely low-temperature resistance
- Leakage-current resistance
Class Grouping
To cover a range of classes, the Product Manual provides for testing of:
Highest class + lowest class + an intermediate class.
This can reduce unnecessary duplicate testing when the grouping conditions are satisfied.
Length Grouping
If a longer glove is tested, shorter glove lengths may also be covered without further testing, subject to the grouping provisions.
Size Grouping
One size in a group can be tested to cover all sizes within that group, subject to the applicable grouping rules.
Scope Based on Manufacturing Capability
The licence scope may be restricted based on manufacturing capabilities, including:
- Mould size/designation
- Mould height for glove length
- Testing capability
BIS Main Tests for Live Working Gloves
The testing programme under IS 13774:2021 is extensive.
1. Composition
Composition is checked according to the applicable requirements.
The Product Manual’s Scheme of Inspection and Testing specifies composition checks on each glove.
2. Dimensions
Dimensions must conform to the applicable requirements.
Dimension checks are specified on each glove.
3. Thickness
Thickness is an important characteristic for both physical and electrical performance.
The routine control calls for three gloves from each control unit, with additional testing of the control unit in case of failure.
4. Workmanship and Finish
Each glove is checked for workmanship and finish.
5. Marking
Marking requirements are checked for each glove.
The product must follow the applicable requirements of Clause 4.6 of IS 13774:2021.
6. Durability of Marking
The durability of marking is also tested.
The Scheme of Inspection and Testing specifies one sample from each control unit.
7. Packaging
Packaging is checked at the prescribed level, with one check for each pair under the Product Manual’s inspection scheme.
8. Instructions for Use
Instructions for use are checked at the package level.
Mechanical Tests
9. Tensile Strength and Elongation at Break
Tensile strength and elongation at break are important mechanical properties.
The Product Manual specifies:
Three samples from each control unit for the type test arrangement, along with sampling tests according to the standard’s sampling plan.
10. Puncture Resistance
Puncture resistance evaluates the glove’s ability to withstand penetration by a specified sharp element.
The Product Manual specifies:
Three samples from each control unit for the type-test arrangement, with sampling testing also carried out according to the standard’s sampling plan.
11. Tension Set
Tension set measures dimensional/elastic recovery behaviour after stretching.
The Product Manual specifies:
Three samples from each control unit for the type-test arrangement.
Electrical Tests
12. Dielectric Type Test
Dielectric testing is one of the most critical requirements for insulating gloves.
The Product Manual specifies:
Three gloves every 15th control unit for the dielectric type test.
13. Dielectric Sampling Test
The sampling test is performed according to the sampling plan in the standard.
14. Dielectric Routine Test
For gloves not subjected to the dielectric type or sampling tests, the routine dielectric test applies to each glove.
The Product Manual identifies a high-voltage testing assembly with:
- AC or DC source
- Milli-ammeter
- Voltmeter
- Auto-transformer for AC dielectric testing
- Appropriate moisture-conditioning arrangement for applicable tests
Ageing and Environmental Tests
15. Ageing Test
Ageing testing evaluates the glove after exposure to specified environmental conditions.
The Product Manual specifies:
Four samples every 30th control unit.
16. Low Temperature Test
The low-temperature test evaluates glove performance under specified cold conditions.
The Product Manual permits subcontracting of this test and specifies:
Three samples every 30th control unit.
17. Flame Retardancy
Where applicable, flame retardancy is tested.
The Product Manual specifies:
One sample every 30th control unit.
Special Category Tests
The additional properties are important when a manufacturer declares a special category.
Category A – Acid Resistance
The glove is evaluated for resistance to the specified acid exposure.
Testing is performed on:
Three samples every 30th control unit.
Category H – Oil Resistance
Oil resistance is tested on:
Three samples every 30th control unit.
Category Z – Ozone Resistance
Ozone resistance is tested on:
Two samples every 30th control unit.
The Product Manual identifies an ozone chamber with temperature control for this test.
Category R – Acid, Oil & Ozone Resistance
Category R combines the requirements associated with acid, oil and ozone resistance.
The Product Manual specifies:
Eight samples every 30th control unit.
Category C – Extremely Low Temperature Resistance
Category C relates to extremely low-temperature performance.
The Product Manual specifies:
Three samples every 30th control unit.
Category F – Leakage Current Resistance
Category F concerns leakage-current resistance.
The Product Manual specifies:
Three samples from each control unit.
For Category F Long Gloves, the Product Manual identifies an additional leakage-current test arrangement.
Tests for Composite Gloves
Composite gloves have additional mechanical-protection requirements.
Abrasion Resistance
The Product Manual specifies:
Five samples from each control unit.
This test is applicable to Composite Gloves only.
Cutting Resistance
The specified sample requirement is:
Two samples from each control unit
for composite gloves.
Tear Resistance
The specified sample requirement is:
Four samples from each control unit
for composite gloves.
BIS Testing Equipment for Live Working Gloves
The current Product Manual provides an indicative test-equipment list. It specifically states that the list is not exhaustive.
Dimensional Testing
Important equipment includes:
- Stainless steel scale
- Micrometer
- Vernier callipers
These are used for dimensions, thickness and other applicable measurements.
Tensile and Mechanical Testing
- Digital tensile testing machine
- Dies
- Vernier callipers
- Puncture-test arrangement
- Metallic needle
These cover tensile strength, elongation, tension set and puncture resistance.
Dielectric Testing
- AC or DC source
- High-voltage testing assembly
- Milli-ammeter
- Voltmeter
- Auto-transformer for AC testing
- Moisture-conditioning arrangement
- Applicable test fixtures
Ageing
- Humidity chamber
- Relevant mechanical-testing equipment
Low-Temperature Testing
- Deep freezer/freezing chamber
- PE plates
- 100 N load
- Stopwatch
- Applicable electrical test arrangement
Flame Retardancy
The Product Manual identifies:
- Flame-test arrangement
- Burner
- Stopwatch
- Suitable gas supply
- Appropriate regulator and flow-metering arrangement
- Draught-free test area
Acid Resistance
- Sulphuric acid solution
- Test liquid
- Hot-air oven
- Humidity chamber
- Lint-free absorbent cloth
- Required mechanical/electrical test equipment
Ozone Resistance
- Ozone chamber
- Temperature controller
- Humidity chamber
- Relevant mechanical/electrical equipment
Extremely Low Temperature
- Cryogenic freezer
- PE plates
- 100 N load
- Relevant testing equipment
Abrasion, Cutting and Tear Tests
For composite gloves, the Product Manual identifies specialized arrangements for:
- Abrasion
- Cutting
- Tear resistance
Laboratory Requirements
The manufacturer is required to maintain a suitably equipped and staffed laboratory for the applicable tests.
The Product Manual requires the manufacturer to:
- Maintain suitable laboratory facilities
- Prepare and implement a calibration plan
- Maintain test records
- Perform tests according to the applicable methods
The manufacturer should therefore establish its testing capability based on the exact proposed licence scope.
External Testing / Subcontracting
The Product Manual permits subcontracting to:
- A laboratory recognized by BIS
- Government laboratories empanelled by BIS
subject to the applicable requirements.
This is particularly useful for specialized tests such as:
- Low-temperature testing
- Flame retardancy
- Acid resistance
- Oil resistance
- Ozone resistance
- Extremely low-temperature resistance
- Other specialized category tests
However, the manufacturer should determine exactly which tests require in-house capability and which can be subcontracted under the current certification requirements.
Control Unit for Live Working Gloves
The Product Manual defines the control unit as:
All gloves of the same type, class, length, category and lining, made out of the same batch of raw materials under similar conditions and manufactured in a day.
This definition is important for:
- Production control
- Sampling
- Test frequency
- Traceability
- Test records
- Product release
Scheme of Inspection and Testing
The Scheme of Inspection and Testing requires quality control throughout the production covered by the licence.
The manufacturer must maintain appropriate records for:
- Composition
- Dimensions
- Thickness
- Workmanship
- Marking
- Mechanical properties
- Dielectric tests
- Ageing
- Environmental properties
- Special categories
- Composite-glove properties
The prescribed levels of control apply to the whole production covered by the certification plan, and the manufacturer must maintain the associated test records.
Marking Requirements
The Product Manual requires marking and labelling according to Clause 4.6 of IS 13774:2021 / IEC 60903:2014.
All production that:
- Conforms to the Indian Standard, and
- Is covered by the BIS licence
should carry the Standard Mark.
The exact marking content and placement should be implemented according to the current standard and approved BIS certification arrangement.
Packaging and Instructions for Use
Packaging is an important part of the certification programme.
The Product Manual specifies:
- Packaging checks on one pair
- Instructions-for-use checks on one package
Manufacturers should therefore ensure that packaging and user instructions are prepared consistently with the applicable product and standard requirements.
Manufacturing Process for Insulating Gloves
A typical manufacturing process may include:
Raw Material Selection → Compound Preparation → Mould Preparation → Glove Forming → Vulcanization/Curing → Washing → Surface Treatment → Inspection → Electrical Testing → Mechanical Testing → Marking → Pairing → Packaging → Final Release
The exact process varies depending on whether the gloves are:
- Insulating
- Composite
- Lined
- Unlined
- Special-category gloves
Process parameters should be controlled so that finished gloves consistently meet the specified requirements.
Important Manufacturing Controls
A manufacturer should maintain control over:
Raw Material
- Polymer/elastomer compound
- Additives
- Colour/pigments
- Batch identification
- Supplier records
Moulds
Mould designation and height are important because they affect:
- Glove size
- Glove length
- Product scope
The Product Manual explicitly recognizes mould size and height as part of manufacturing capability assessment.
Vulcanization
Important parameters may include:
- Temperature
- Time
- Pressure
- Cure conditions
Final Inspection
- Dimensions
- Thickness
- Surface finish
- Workmanship
- Marking
- Electrical performance
- Mechanical properties
BIS Certification Process for Live Working Gloves
The typical process is:
Product Identification → IS 13774:2021 Applicability → Product Classification → Type Selection → Class Selection → Special Category Selection → Size/Length/Lining Selection → Grouping → Factory Assessment → Laboratory Readiness → Sample Preparation → Testing → Documentation → BIS Application → Factory Inspection → Compliance → BIS Licence → Standard Marking → Post-Licence Compliance
The exact procedure depends on the manufacturer’s scope and factory setup.
Documents Required for BIS Certification
Common documents may include:
- Company incorporation/registration documents
- Factory address proof
- Factory ownership or lease documents
- Authorized signatory details
- Manufacturing process flow chart
- Factory layout
- Machinery list
- Mould details
- Testing equipment list
- Calibration certificates
- Product specifications
- Glove classification details
- Size and length details
- Raw-material details
- Internal test records
- Laboratory test reports
- Quality-control documents
- Packaging details
- Instructions for use
- Applicable declarations and undertakings
- Trademark/brand documents where applicable
The final checklist should be prepared according to the current BIS application and product-specific requirements.
Factory Inspection for Live Working Gloves
Before BIS assessment, the manufacturer should be prepared to demonstrate:
Production Facilities
- Compound preparation
- Moulding/forming
- Curing/vulcanization
- Washing
- Finishing
- Inspection
Testing Facilities
- Dimensional measurement
- Thickness
- Tensile testing
- Puncture resistance
- Tension set
- Dielectric testing
- Ageing
- Other tests applicable to the proposed scope
Quality Control
- Raw-material inspection
- Batch identification
- Production control
- Testing records
- Calibration
- Final inspection
- Rejection control
Qualitance India assists manufacturers in reviewing these requirements before the applicable BIS factory assessment.
BIS Testing Charges for IS 13774:2021
Current BIS LIMS shows an active testing facility for IS 13774:2021 – Live Working Gloves of Insulating Material.
One current laboratory listing from ERDA, Vadodara displays a testing charge of ₹48,750 excluding taxes for the listed scope. The displayed breakup includes, among other items:
- Thickness: ₹2,900
- Other IS 13774 test items
- Dielectric test: ₹2,050
- Proof test: ₹1,300
- Ageing test: ₹9,650
- Low-temperature test: ₹4,800
- Other applicable tests
These are laboratory-specific displayed charges and can change according to:
- Glove type
- Class
- Special category
- Scope of testing
- Laboratory
- Additional tests
- Sample requirements
- Applicable taxes
The latest BIS LIMS scope should therefore be checked before submitting samples.
Cost of BIS Certification for Live Working Gloves
The total certification cost includes more than laboratory testing.
Potential expenses include:
- BIS application charges
- Product testing
- Specialized environmental tests
- Dielectric testing
- Sample preparation
- Factory preparation
- Calibration
- Testing equipment
- Documentation
- Inspection-related expenses
- Consultancy charges
- Post-licence compliance
Composite gloves and gloves with special categories can require additional testing and therefore may have higher certification costs.
How Long Does BIS Certification Take?
The timeline depends on:
- Product classification
- Number of classes
- Number of sizes
- Length range
- Special categories
- Lined/unlined construction
- Composite or insulating type
- Testing requirements
- Laboratory availability
- Factory readiness
- Documentation
- BIS inspection scheduling
- Corrective actions
Specialized tests such as ageing, low-temperature, ozone or other environmental tests can increase the overall testing schedule.
Common Reasons for BIS Certification Delays
Incorrect Product Classification
The manufacturer may not correctly identify insulating versus composite construction.
Excessive Scope
Trying to include too many classes, lengths, sizes and special categories without adequate facilities can complicate certification.
Incorrect Grouping
Grouping must be planned according to the current Product Manual.
Dielectric Test Failure
Electrical insulation performance is critical and failure can prevent certification.
Mechanical Test Failure
Tensile, elongation, puncture or tension-set failures can require corrective action.
Thickness Variation
Poor process control can lead to inconsistent thickness.
Ageing Failure
Material degradation under the specified ageing conditions can affect conformity.
Special Category Failure
Acid, oil, ozone or low-temperature properties may fail if the compound and manufacturing process are not suitable.
Composite Glove Failure
Composite gloves have additional abrasion, cutting and tear requirements.
Calibration Issues
Test equipment must have appropriate calibration and records.
Incomplete Documentation
Missing factory, product, testing or packaging information can create delays.
Who Needs BIS Certification for Live Working Gloves?
The certification requirements are relevant to manufacturers producing regulated live-working insulating gloves for the Indian market.
This may include:
- Electrical safety equipment manufacturers
- Rubber glove manufacturers
- Electrical PPE manufacturers
- High-voltage safety equipment manufacturers
- Utility-sector suppliers
- Power-sector suppliers
- Government suppliers
- Electrical contractors’ approved suppliers
- Industrial safety equipment manufacturers
Importers and traders should separately verify their regulatory responsibilities.
Applications of Live Working Gloves
Live working gloves may be used by professionals working in:
- Electrical distribution
- Power transmission
- Electrical maintenance
- Substations
- Industrial electrical systems
- Utility maintenance
- Electrical installation
- Power-generation facilities
- High-voltage service environments
The actual class and glove configuration should be selected according to the intended application and applicable safety requirements.
Benefits of BIS Certification
Electrical Safety Compliance
The certification framework includes dielectric testing and other protective characteristics.
Product Quality
Mechanical and physical testing helps establish consistent performance.
Buyer Confidence
Certified electrical PPE can provide greater assurance to professional buyers.
Regulatory Compliance
For regulated products, BIS certification supports mandatory compliance.
Government & Institutional Supply
A valid BIS licence can support procurement where the certification is specified.
Better Product Traceability
Control-unit requirements and records provide a structured quality-control system.
BIS Certification Consultancy for Live Working Gloves
Qualitance India provides complete consultancy for Live Working Gloves of Insulating Material as per IS 13774:2021 / IEC 60903:2014.
Product & Standard Identification
We identify the correct standard and certification route.
Product Scope Assessment
We review:
- Insulating or Composite
- Class 00 to Class 4
- Special categories
- Size
- Length
- Lining
Grouping Guidance
We help determine suitable testing combinations to establish the proposed licence scope.
Sample Planning
We assist with the prescribed 15-pair sample and additional samples where required.
Testing Coordination
We coordinate mechanical, dielectric, environmental and special-category tests.
Documentation Support
We prepare and organize the documents required for BIS certification.
Factory Inspection Preparation
We review machinery, moulds, testing equipment, calibration and production controls.
BIS Application Filing
We assist with preparing and submitting the certification application.
Factory Inspection Assistance
We help prepare the manufacturer for BIS assessment.
Query & Compliance Support
We assist with technical and documentary observations.
Licence Processing
We support the certification process through the licence stage.
Post-Licence Compliance
We assist with renewal, scope-related activities and ongoing BIS compliance.
Quick BIS Certification Checklist
Before applying for BIS certification:
☑ IS 13774:2021 applicability confirmed
☑ IEC 60903:2014 alignment understood
☑ Insulating/Composite type selected
☑ Class 00/0/1/2/3/4 selected
☑ Special category selected, if applicable
☑ Size finalized
☑ Length finalized
☑ Lined/Unlined finalized
☑ Grouping reviewed
☑ Mould sizes available
☑ Mould heights available
☑ Testing equipment available
☑ High-voltage test facility available
☑ Mechanical testing facility available
☑ Environmental test arrangement available
☑ Calibration certificates available
☑ Control-unit procedure established
☑ 15-pair representative sample arranged
☑ Laboratory testing completed
☑ BIS documentation prepared
☑ Factory ready for assessment
☑ Marking and packaging arrangements ready
Frequently Asked Questions
1. What is IS 13774:2021?
IS 13774:2021 is the Indian Standard for Live Working Gloves of Insulating Material, aligned with IEC 60903:2014.
2. Is BIS certification mandatory for live working gloves?
IS 13774:2021 is included in the mandatory electrical-products certification framework and is currently listed by BIS under Scheme-I.
3. Which BIS scheme applies?
Certification is under Scheme-I.
4. What is the current BIS Product Manual?
The current Product Manual identified is PM/IS 13774/IEC 60903/2/February 2022.
5. What types of gloves are covered?
The licence scope identifies Insulating and Composite gloves.
6. What classes are covered?
Classes 00, 0, 1, 2, 3 and 4 are covered.
7. What special categories are covered?
The categories are A, H, Z, R, C and F.
8. What does Category A mean?
Category A relates to acid resistance.
9. What does Category H mean?
Category H relates to oil resistance.
10. What does Category Z mean?
Category Z relates to ozone resistance.
11. What does Category R mean?
Category R combines acid, oil and ozone resistance.
12. What does Category C mean?
Category C relates to extremely low-temperature resistance.
13. What does Category F mean?
Category F relates to leakage-current resistance.
14. What sizes are covered?
The Product Manual lists sizes 7 through 12 in half-size increments. Other sizes may be agreed between manufacturer and client subject to the applicable requirements.
15. What standard lengths are covered?
The listed lengths are 280, 360, 410, 460 and 800 mm Long.
16. Are both lined and unlined gloves covered?
Yes. Both lined and unlined gloves are identified in the licence scope.
17. What is the BIS sample size?
The Product Manual specifies 15 pairs of gloves, with additional samples where required according to the glove type.
18. Is grouping available?
Yes. Grouping is based on type, class, special category, size, length and lining.
19. Are insulating and composite gloves grouped together?
No. Different glove types are treated as separate groups.
20. Are lined and unlined gloves grouped together?
No. They are considered separate groups.
21. Can one test cover different glove lengths?
Yes. Under the grouping provisions, a longer glove can cover shorter lengths without further testing, subject to the applicable conditions.
22. Can one size cover all sizes?
A glove of one size within a group can be used to cover all sizes in that group under the grouping provisions.
23. How are different classes grouped?
To cover a range of classes, the Product Manual provides for testing the highest, lowest and an intermediate class.
24. Do special categories require separate testing?
Yes. Each category and each combination of categories must be tested separately.
25. What are the main mechanical tests?
Important mechanical tests include tensile strength, elongation at break, puncture resistance and tension set.
26. Is dielectric testing required?
Yes. Dielectric type, sampling and routine tests are included in the certification programme.
27. Is ageing testing required?
Yes. Ageing testing is included in the Scheme of Inspection and Testing.
28. Are composite gloves tested for cutting and tear resistance?
Yes. Composite gloves have additional abrasion, cutting and tear resistance requirements.
29. Is an in-house laboratory required?
A suitably equipped and staffed laboratory is required for applicable tests, while specified tests may be subcontracted to BIS-recognized or Government laboratories under the Product Manual provisions.
30. What is the control unit?
All gloves of the same type, class, length, category and lining, made from the same batch of raw materials under similar conditions and manufactured in a day constitute a control unit.
31. What equipment is required for dielectric testing?
The Product Manual identifies high-voltage testing equipment, AC/DC source, milli-ammeter, voltmeter and related test arrangements.
32. Is special equipment required for ozone testing?
Yes. An ozone chamber with temperature control is identified for Category Z testing.
33. Is low-temperature testing required?
Yes, where applicable. The Product Manual specifies low-temperature testing and allows it to be subcontracted under the stated provisions.
34. What are current testing charges?
One current BIS LIMS laboratory listing shows ₹48,750 excluding taxes for its displayed IS 13774:2021 scope. Actual charges depend on the laboratory and exact testing scope.
35. Does every laboratory offer every special test?
No. Testing capability varies by laboratory and scope, so the laboratory should be selected according to the actual glove configuration and required tests.
36. Is calibration required?
Yes. The manufacturer must prepare and implement a calibration plan for the testing equipment.
37. Are test records required?
Yes. The manufacturer must maintain records for tests performed to establish conformity.
38. Is Standard Marking required?
Yes. Production conforming to the Indian Standard and covered by the licence should be marked with the Standard Mark.
39. Can a manufacturer apply for several classes?
Yes, subject to the applicable grouping, testing and manufacturing capabilities.
40. Can Qualitance India help with BIS certification for live working gloves?
Yes. Qualitance India provides complete consultancy for product assessment, classification, grouping, sample planning, testing coordination, documentation, factory inspection preparation, BIS application, licence processing and post-licence compliance.
Related BIS Certification Services
Qualitance India also provides consultancy for:
- BIS Certification
- ISI Mark Certification
- Electrical Safety Product Certification
- Electrical PPE Certification
- Insulating Gloves Certification
- Insulating Mats Certification
- BIS Scheme-I Certification
- BIS Licence Renewal
- BIS Scope Extension
- Product Testing Coordination
- BIS Documentation
- Factory Inspection Assistance
- Quality Control Order Applicability
- Product Grouping Guidance
- Technical Compliance Support
Related Electrical Safety Products
Manufacturers may also require BIS certification consultancy for:
- Insulating Mats for Electrical Purposes – IS 15652
- Electrical Safety Helmets
- Electrical Protective Equipment
- Insulating Sleeves
- Live Working Tools
- Electrical Accessories
- Other regulated electrical safety products
The exact Indian Standard should always be checked against the product before certification.
Why Choose Qualitance India?
Qualitance India provides end-to-end BIS Certification consultancy for manufacturers of electrical safety products.
Product Assessment
We identify the correct standard and certification route.
Classification & Scope
We help define the type, class, category, size, length and lining requirements.
Grouping Guidance
We assist with sample selection and licence-scope planning.
Testing Coordination
We coordinate mechanical, dielectric and specialized environmental testing.
Documentation Support
We assist with BIS application documents and technical records.
Factory Preparation
We review moulds, machinery, laboratory facilities, calibration and quality-control systems.
Application Support
We assist in BIS application filing and follow-up.
Factory Inspection Assistance
We help prepare the manufacturing unit for BIS assessment.
Query & Compliance Support
We assist with technical and documentary observations.
Licence Processing
We support the certification process through the licence stage.
Post-Licence Compliance
We provide ongoing support for renewal, scope and other applicable BIS requirements.
Contact Qualitance India
Qualitance India – Your Certification & Compliance Partner
Phone: +91 93106 15170
Email: info@qualitanceindia.com
Website: https://qualitanceindia.com/
For BIS Certification of Live Working Gloves of Insulating Material as per IS 13774:2021 / IEC 60903:2014, Qualitance India provides complete consultancy covering product classification, grouping, sample planning, testing, documentation, factory inspection preparation, BIS application, licence processing and continuing compliance.
Conclusion
Live Working Gloves of Insulating Material are safety-critical electrical protective products that require reliable insulation and mechanical performance. IS 13774:2021 / IEC 60903:2014 provides the technical framework for evaluating these gloves across electrical, mechanical, dimensional and environmental characteristics.
The BIS certification scope includes Insulating and Composite Gloves, Classes 00, 0, 1, 2, 3 and 4, special categories A, H, Z, R, C and F, multiple sizes and lengths, and lined or unlined construction.
The current BIS Product Manual requires a 15-pair sample, with additional samples depending on glove type, and establishes detailed requirements for tensile strength, elongation, puncture resistance, tension set, dielectric testing, ageing, low temperature, flame retardancy, special resistance categories and additional tests for composite gloves.
For manufacturers, successful BIS certification requires careful scope planning, appropriate moulds and production facilities, suitable laboratory arrangements, calibration, representative samples, testing, documentation and continuous production control.
Qualitance India provides end-to-end BIS Certification consultancy for Live Working Gloves, helping manufacturers manage product classification, grouping, testing, documentation, factory assessment, BIS application and post-licence compliance.
Need BIS Certification for Live Working Gloves of Insulating Material as per IS 13774:2021? Contact Qualitance India for complete BIS licence and compliance support.