Tee and Strap Hinges are important hardware components used for doors, gates, shutters, boxes and other applications where a strong and durable hinged connection is required. These hinges are commonly used in residential, commercial, agricultural, industrial and architectural applications.<\/p>\n
Because hinges are load-bearing hardware components, their dimensions, material, construction, workmanship, finish, screw-hole arrangement, knuckles and hinge-pin assembly need to be properly controlled.<\/p>\n
In India, IS 206:2010 \u2013 Tee and Strap Hinges \u2013 Specification<\/strong> specifies requirements for Tee and Strap Hinges. The standard is identified as the Fifth Revision<\/strong> in current BIS laboratory records. (bis.gov.in<\/a>)<\/p>\n BIS currently includes IS 206:2010 under the compulsory Hinges Quality Control Order<\/strong> framework. The current Hinges (Quality Control) Order, 2025 requires covered hinges to conform to the applicable Indian Standard and bear the Standard Mark under a BIS licence according to Scheme-I. (bis.gov.in<\/a>)<\/p>\n Qualitance India provides end-to-end BIS Certification consultancy for Tee and Strap Hinge manufacturers, including product assessment, documentation, product testing coordination, grouping guidance, factory inspection preparation and BIS licence support.<\/p>\n Tee and Strap Hinges are mechanical hardware fittings used to connect a movable door, gate, shutter, box or similar structure to a fixed frame or supporting structure.<\/p>\n A Tee Hinge generally has a narrow mounting portion connected to a wider horizontal strap, creating a shape resembling the letter \u201cT\u201d.<\/p>\n Tee Hinges are commonly used for:<\/p>\n Strap Hinges have an elongated strap-like mounting member and are commonly used for:<\/p>\n The particular hinge type and size determine the applicable construction and dimensional requirements.<\/p>\n The applicable Indian Standard is:<\/p>\n IS 206:2010 \u2013 Tee and Strap Hinges \u2013 Specification<\/strong><\/p>\n The standard is identified as the Fifth Revision<\/strong> in current BIS laboratory records. (lims.bis.gov.in<\/a>)<\/p>\n The BIS Product Manual available for certification is:<\/p>\n PM\/IS 206\/1\/December 2022<\/strong><\/p>\n The Product Manual identifies:<\/p>\n Yes.<\/p>\n The Hinges (Quality Control) Order, 2025<\/strong> specifically lists:<\/p>\n IS 206:2010 \u2013 Tee and Strap Hinges<\/strong><\/p>\n under the Hinges category. The Order requires the specified hinges to conform to the relevant Indian Standard and bear the Standard Mark under a BIS licence according to Scheme-I. (bis.gov.in<\/a>)<\/p>\n The 2025 Order superseded the earlier Hinges Quality Control Order, 2024. (bis.gov.in<\/a>)<\/p>\n The current BIS Scheme-I listing continues to include IS 206:2010 \u2013 Tee and Strap Hinges<\/strong> under the Hinges QCO framework. (bis.gov.in<\/a>)<\/p>\n The Hinges (Quality Control) Order, 2025 was notified on 21 March 2025<\/strong> and came into force on publication in the Official Gazette.<\/p>\n It covers:<\/p>\n For the listed products, the Order requires conformity with the applicable Indian Standard and use of the Standard Mark under a BIS licence.<\/p>\n The Order provides an implementation date of 1 July 2025<\/strong> for the listed hinge products. (bis.gov.in<\/a>)<\/p>\n BIS’s current Scheme-I page records additional regulatory notifications associated with the Hinges QCO, including:<\/p>\n The Transition Facilitation Order introduced a separate facilitation mechanism for certain goods covered by notified QCOs. It does not remove the underlying product-quality requirements. Manufacturers should check the latest applicable notification before relying on any transition arrangement. (worldtradescanner.com<\/a>)<\/p>\n The BIS Product Manual classifies Tee Hinges into the following varieties:<\/p>\n The Product Manual identifies:<\/p>\n The manufacturer must declare the varieties proposed to be covered by the BIS licence.<\/p>\n Product size is identified according to dimension A<\/strong> in the relevant tables of IS 206:2010.<\/p>\n The Product Manual specifies that the grouping is based on:<\/p>\n Type + Size<\/strong><\/p>\n and refers manufacturers to Tables 2 to 12 of IS 206:2010 for the applicable size designations. (bis.gov.in<\/a>)<\/p>\n Grouping is a very important part of the BIS certification process.<\/p>\n As per the Product Manual, Tee and Strap Hinges are classified based on:<\/p>\n The applicable Tee Hinge and Strap Hinge categories are considered separately.<\/p>\n The size is designated by dimension A<\/strong> according to the relevant product tables.<\/p>\n The Product Manual specifies that:<\/p>\n One sample from each type having the minimum and maximum size shall be drawn to cover all sizes of hinges in that type tested.<\/strong> (bis.gov.in<\/a>)<\/p>\n Therefore, manufacturers should prepare a proper type-and-size matrix before applying for certification.<\/p>\n The manufacturer must declare the varieties intended to be covered by the licence, and BIS may restrict the licence scope according to manufacturing and testing capabilities. (bis.gov.in<\/a>)<\/p>\n The Product Manual specifies:<\/p>\n 1 No.<\/strong><\/p>\n as the product sample size for Tee and Strap Hinges. (bis.gov.in<\/a>)<\/p>\n Because the grouping provisions require minimum and maximum sizes for each type, manufacturers should coordinate sample selection carefully.<\/p>\n The current Product Manual identifies the following raw materials:<\/p>\n Mild steel sheet \u2013 Grade 0 of IS 1079<\/strong><\/p>\n Mild steel wire \u2013 minimum 1\/4H grade of IS 280<\/strong><\/p>\n These requirements are specifically identified in the BIS Product Manual for IS 206:2010. (bis.gov.in<\/a>)<\/p>\n Manufacturers should maintain appropriate material records and traceability.<\/p>\n Important documents may include:<\/p>\n A typical manufacturing process can include the following stages.<\/p>\n Steel sheets and wire are received and checked against the applicable material requirements.<\/p>\n Sheet material is cut into the required hinge-flap or strap shapes.<\/p>\n The hinge components are formed according to the required geometry.<\/p>\n The hinge knuckles are formed to accommodate the hinge pin.<\/p>\n The hinge pin is produced from the specified wire or other applicable material.<\/p>\n Screw holes are produced according to the applicable dimensions and positions.<\/p>\n The pin is assembled with the hinge flaps\/strap components.<\/p>\n The hinge receives the required surface finish.<\/p>\n Dimensions, workmanship, finish and other requirements are checked.<\/p>\n Conforming hinges are packed and marked according to BIS requirements.<\/p>\n Current BIS laboratory listings for IS 206:2010 identify testing areas covering dimensions and tolerances, workmanship, finish, types, manufacture, knuckles, screw holes, packing and marking. (lims.bis.gov.in<\/a>)<\/p>\n The hinge type is checked against the applicable classification in IS 206.<\/p>\n Dimensional inspection is one of the principal requirements.<\/p>\n Depending on the hinge type, dimensions can include:<\/p>\n Current BIS laboratory scopes specifically identify dimensional requirements against the relevant tables and figures. (lims.bis.gov.in<\/a>)<\/p>\n The specified dimensional tolerances must be satisfied.<\/p>\n The general method of manufacture and construction must comply with the standard.<\/p>\n Knuckle construction and dimensions are important for smooth hinge operation and durability.<\/p>\n The hinge pin must comply with the applicable material and dimensional requirements.<\/p>\n The standard specifies requirements for:<\/p>\n BIS laboratory listings specifically identify these checks. (lims.bis.gov.in<\/a>)<\/p>\n The finished hinges should be free from unacceptable workmanship defects.<\/p>\n Current BIS laboratory scopes identify Clause 6 \u2013 Workmanship<\/strong> as a testing requirement. (lims.bis.gov.in<\/a>)<\/p>\n The surface finish is checked against the applicable standard requirements.<\/p>\n The packaging should protect the hinges and comply with the applicable packing requirements.<\/p>\n Product marking is checked against the applicable requirements.<\/p>\n Dimensions play a critical role because Tee and Strap Hinges must fit the intended door, gate or shutter assembly.<\/p>\n The manufacturer should maintain suitable dimensional-control instruments such as:<\/p>\n The current BIS laboratory data identifies dimensional and tolerance testing as a principal IS 206 requirement. (lims.bis.gov.in<\/a>)<\/p>\n Correct screw-hole positioning is particularly important for installation.<\/p>\n The applicable checks can include:<\/p>\n The BIS laboratory scope specifically lists these aspects for IS 206:2010. (lims.bis.gov.in<\/a>)<\/p>\n The knuckle is the cylindrical section through which the hinge pin passes.<\/p>\n The manufacturer should ensure:<\/p>\n These aspects are part of the manufacturing requirements of IS 206.<\/p>\n The standard includes requirements for workmanship and finish.<\/p>\n The finished hinge should be properly formed and should not contain unacceptable defects affecting appearance, installation or performance.<\/p>\n Current BIS laboratory listings identify separate testing charges for:<\/p>\n under IS 206:2010. (lims.bis.gov.in<\/a>)<\/p>\n The BIS Product Manual refers to Annex B<\/strong> for the applicable test-equipment requirements. (bis.gov.in<\/a>)<\/p>\n Typical equipment can include:<\/p>\n The actual equipment should be finalized according to the manufacturer’s proposed product types and sizes.<\/p>\n The manufacturer should maintain appropriate inspection and testing facilities for applicable requirements under the Scheme of Inspection and Testing.<\/p>\n The facility should include:<\/p>\n Where specific testing is permitted to be subcontracted, the applicable external laboratory route may be used according to BIS requirements.<\/p>\n A suitable Quality Assurance Plan for Tee and Strap Hinges should include:<\/p>\n The QAP should be aligned with the applicable Scheme of Inspection and Testing.<\/p>\n The applicable control-unit definition should be implemented according to the current Scheme of Inspection and Testing.<\/p>\n The manufacturer should maintain production traceability according to relevant factors such as:<\/p>\n This helps ensure that only conforming products are released under the BIS certification.<\/p>\n During factory inspection, BIS may assess:<\/p>\n The manufacturer should demonstrate control over mild-steel sheet and wire.<\/p>\n The production process should correspond to the declared product scope.<\/p>\n BIS may verify the manufacturer’s ability to produce the required components consistently.<\/p>\n Hole dimensions and positions should be appropriately controlled.<\/p>\n Inspection and testing equipment should be available and suitable.<\/p>\n Applicable measuring equipment should have valid calibration or verification records.<\/p>\n Records may include:<\/p>\n IS 206:2010 contains provisions for marking Tee and Strap Hinges and their packaging.<\/p>\n The standard requires individual hinges to carry specified identification information, including the applicable hinge type and size, while package labelling includes manufacturer\/trade-mark, type and size information. (law.resource.org<\/a>)<\/p>\n The use of the BIS Standard Mark is governed by the BIS certification framework and the conditions of the licence.<\/p>\n Manufacturers must ensure that:<\/p>\n Current BIS LIMS records show multiple laboratories with active testing scopes for:<\/p>\n IS 206 (2010) \u2013 Tee and Strap Hinges \u2013 Specification (Fifth Revision)<\/strong>. (lims.bis.gov.in<\/a>)<\/p>\n Current laboratory listings show different testing charges and scopes.<\/p>\n Examples include:<\/p>\n Hindustaan Testing Solutions LLP, Ambala:<\/strong> approximately \u20b93,500<\/strong> for its displayed scope. (lims.bis.gov.in<\/a>)<\/p>\n IDMA Laboratories Limited, Panchkula:<\/strong> approximately \u20b98,200<\/strong> for the displayed scope, with separate information for material-composition testing. (lims.bis.gov.in<\/a>)<\/p>\n Other current BIS LIMS listings show testing charges around \u20b97,500\u2013\u20b98,000<\/strong> for displayed IS 206 scopes. (lims.bis.gov.in<\/a>)<\/p>\n These are laboratory-specific testing charges<\/strong>, not the complete BIS certification cost.<\/p>\n The total certification cost depends on:<\/p>\n Because the grouping provisions involve minimum and maximum sizes for each type, scope planning can have a direct effect on testing cost.<\/p>\n Typical documents may include:<\/p>\n The exact documentation depends on the manufacturer’s business structure and proposed licence scope.<\/p>\n Tee and Strap Hinge manufacturers may face delays because of:<\/p>\n A pre-assessment of the product range and factory facilities can help reduce these issues.<\/p>\n Manufacturers producing covered Tee and Strap Hinges for the Indian market should comply with the applicable Hinges QCO requirements.<\/p>\n The requirement can be relevant to:<\/p>\n The exact applicability of exemptions or transition provisions should be checked against the latest government notifications.<\/p>\n BIS certification can help manufacturers demonstrate compliance with the applicable Indian Standard and regulatory requirements.<\/p>\n Benefits include:<\/p>\n Manufacturer Assessment \u2192 Product Type & Size Finalization \u2192 Grouping Assessment \u2192 Documentation \u2192 BIS Application \u2192 Sample Testing \u2192 Factory Inspection \u2192 Compliance Closure \u2192 BIS Licence \u2192 Standard Marking<\/strong><\/p>\n Qualitance India provides professional BIS Certification consultancy for Tee and Strap Hinge manufacturers.<\/p>\n Our assistance can include:<\/p>\n We help manufacturers organize the technical, testing and documentation requirements needed for BIS certification.<\/p>\n It is the BIS conformity-assessment process through which a manufacturer demonstrates that Tee and Strap Hinges conform to IS 206:2010 and obtains authorization to use the BIS Standard Mark within the approved scope.<\/p>\n The applicable standard is IS 206:2010 \u2013 Tee and Strap Hinges \u2013 Specification<\/strong>, identified as the Fifth Revision. (lims.bis.gov.in<\/a>)<\/p>\n Yes. IS 206:2010 is listed in the Hinges Quality Control Order framework and the current BIS Scheme-I product list. (bis.gov.in<\/a>)<\/p>\n Certification is under Scheme-I<\/strong> of the BIS Conformity Assessment Regulations, 2018. (bis.gov.in<\/a>)<\/p>\n The accessible BIS Product Manual is PM\/IS 206\/1\/December 2022<\/strong>. (bis.gov.in<\/a>)<\/p>\n The Product Manual specifies 1 No.<\/strong> as the sample size. (bis.gov.in<\/a>)<\/p>\n The Product Manual specifies:<\/p>\n The Product Manual identifies seven Tee Hinge varieties:<\/p>\n The identified varieties are:<\/p>\n Grouping is based on hinge type and size<\/strong>. (bis.gov.in<\/a>)<\/p>\n Size is designated by dimension A<\/strong> according to the relevant tables of IS 206:2010. (bis.gov.in<\/a>)<\/p>\n The Product Manual specifies one sample from each type having the minimum and maximum size<\/strong> to cover the sizes in that tested type, subject to the applicable grouping provisions. (bis.gov.in<\/a>)<\/p>\n No. The grouping provisions distinguish between different hinge types and require representative minimum and maximum sizes for each type. (bis.gov.in<\/a>)<\/p>\n Major requirements include:<\/p>\n Current BIS LIMS records confirm these testing areas. (lims.bis.gov.in<\/a>)<\/p>\n Yes. Dimensional conformity and tolerances are important requirements under IS 206:2010. (lims.bis.gov.in<\/a>)<\/p>\n Yes. Current BIS laboratory scopes identify screw-hole dimensions, number and positioning requirements. (lims.bis.gov.in<\/a>)<\/p>\n Yes. Knuckle construction and dimensions form part of the manufacturing requirements. (lims.bis.gov.in<\/a>)<\/p>\n Yes. The applicable pin construction and dimensional requirements must comply with IS 206:2010.<\/p>\n Yes. Workmanship is separately identified in current BIS laboratory scopes. (lims.bis.gov.in<\/a>)<\/p>\n Yes. Finish is a separate conformity requirement. (lims.bis.gov.in<\/a>)<\/p>\n The standard contains packing requirements, and current BIS LIMS entries identify Clause 8 \u2013 Packing. (lims.bis.gov.in<\/a>)<\/p>\n Yes. Current BIS laboratory scopes include marking requirements. (lims.bis.gov.in<\/a>)<\/p>\n Current BIS LIMS examples show approximately \u20b93,500 to \u20b98,200<\/strong> for displayed IS 206 scopes, depending on laboratory and test scope. (lims.bis.gov.in<\/a>)<\/p>\n No. Laboratory charges are separate from BIS certification-related expenses.<\/p>\n Factory assessment\/inspection is an important part of the BIS licensing process, where manufacturing, quality-control and testing arrangements are assessed.<\/p>\n Typical documents include company details, factory layout, machinery, manufacturing process, product drawings, raw-material information, testing facilities, calibration records and quality documents.<\/p>\n The licence scope can contain the manufacturer\u2019s declared Tee and Strap Hinge varieties, subject to applicable grouping, testing and BIS approval requirements.<\/p>\n The grouping provisions provide for representative minimum and maximum sizes for each type, subject to the applicable conditions and the final BIS-approved scope. (bis.gov.in<\/a>)<\/p>\n The manufacturer must investigate the non-conformity, implement appropriate corrective action and follow the applicable BIS testing\/compliance procedure.<\/p>\n Yes. Qualitance India provides end-to-end support including product assessment, grouping, documentation, laboratory coordination, testing, factory inspection preparation and BIS licence support.<\/p>\n Qualitance India also provides BIS consultancy for manufacturers of:<\/p>\n Steel Butt Hinges | Stainless Steel Butt Hinges | Non-Ferrous Metal Butt Hinges | Parliament Hinges | Continuous\/Piano Hinges | Steel Back Flap Hinges | Double-Acting Spring Hinges | Cabinet Hinges | Rim Latches | Door Hardware | Other Regulated Products<\/strong><\/p>\n Our services include:<\/p>\n BIS Certification Consultancy | BIS Licence | ISI Mark Certification | Product Testing | Documentation Support | Factory Inspection Assistance | Quality Plan Preparation | Technical Compliance Support | Scope Extension | Licence Renewal | End-to-End BIS Support<\/strong><\/p>\n Qualitance India<\/strong> Phone:<\/strong> +91 93106 15170 Manufacturers of Tee and Strap Hinges can contact Qualitance India for assistance with IS 206:2010 BIS Certification<\/strong>, product grouping, sample planning, laboratory testing, documentation, factory inspection preparation and BIS licence support.<\/p>\n Tee and Strap Hinges are widely used hardware components for doors, gates, shutters, boxes and other movable structures. Their performance depends on correct dimensions, material quality, knuckle construction, hinge-pin arrangement, screw-hole positioning, workmanship and surface finish.<\/p>\n IS 206:2010 \u2013 Tee and Strap Hinges \u2013 Specification<\/strong> is identified as the Fifth Revision and remains included in the compulsory BIS certification framework for hinges. The current BIS Product Manual PM\/IS 206\/1\/December 2022<\/strong> specifies 1 sample<\/strong>, identifies specific Tee and Strap Hinge varieties, and provides grouping based on type and size<\/strong>. (bis.gov.in<\/a>)<\/p>\n The Hinges Quality Control Order, 2025 specifically lists IS 206:2010 and requires covered products to conform to the applicable Indian Standard and bear the Standard Mark under a BIS licence according to Scheme-I. (bis.gov.in<\/a>)<\/p>\nWhat Are Tee and Strap Hinges?<\/h2>\n
Tee Hinges<\/h3>\n
\n
Strap Hinges<\/h3>\n
\n
BIS Standard for Tee and Strap Hinges<\/h2>\n
\n
Is BIS Certification Mandatory for Tee and Strap Hinges?<\/h2>\n
Current Hinges Quality Control Order<\/h2>\n
\n
Current 2026 Regulatory Update<\/h2>\n
\n
Types of Tee Hinges Covered<\/h2>\n
Light Weight<\/h3>\n
\n
Medium Weight<\/h3>\n
\n
Heavy Weight<\/h3>\n
\n
Types of Strap Hinges Covered<\/h2>\n
\n
Product Sizes<\/h2>\n
BIS Product Grouping for Tee and Strap Hinges<\/h2>\n
Type<\/h3>\n
Size<\/h3>\n
Representative Samples<\/h3>\n
BIS Sample Size<\/h2>\n
Raw Material Requirements<\/h2>\n
Mild Steel Sheet<\/h3>\n
Mild Steel Wire<\/h3>\n
\n
Manufacturing Process of Tee and Strap Hinges<\/h2>\n
1. Raw Material Inspection<\/h3>\n
2. Cutting<\/h3>\n
3. Forming<\/h3>\n
4. Knuckle Formation<\/h3>\n
5. Pin Manufacturing<\/h3>\n
6. Hole Formation<\/h3>\n
7. Assembly<\/h3>\n
8. Finishing<\/h3>\n
9. Inspection<\/h3>\n
10. Packing and Marking<\/h3>\n
Major BIS Tests for Tee and Strap Hinges<\/h2>\n
1. Type Verification<\/h3>\n
2. Dimensions<\/h3>\n
\n
3. Tolerances<\/h3>\n
4. Manufacture<\/h3>\n
5. Knuckles<\/h3>\n
6. Hinge Pin<\/h3>\n
7. Screw Holes<\/h3>\n
\n
8. Workmanship<\/h3>\n
9. Finish<\/h3>\n
10. Packing<\/h3>\n
11. Marking<\/h3>\n
Dimensions and Tolerances<\/h2>\n
\n
Screw-Hole Requirements<\/h2>\n
\n
Knuckle and Pin Requirements<\/h2>\n
\n
Workmanship and Finish<\/h2>\n
\n
Test Equipment Required<\/h2>\n
\n
In-House Testing Facility<\/h2>\n
\n
Quality Assurance Plan<\/h2>\n
\n
Control Unit for Tee and Strap Hinges<\/h2>\n
\n
Factory Inspection for BIS Certification<\/h2>\n
Raw Material<\/h3>\n
Manufacturing<\/h3>\n
Knuckle and Pin Manufacturing<\/h3>\n
Screw-Hole Production<\/h3>\n
Laboratory<\/h3>\n
Calibration<\/h3>\n
Quality Records<\/h3>\n
\n
BIS Marking Requirements<\/h2>\n
\n
BIS Testing Laboratories for IS 206:2010<\/h2>\n
Total BIS Certification Cost for Tee and Strap Hinges<\/h2>\n
\n
Documents Required for BIS Certification<\/h2>\n
\n
Common Reasons for BIS Certification Delays<\/h2>\n
\n
Who Needs BIS Certification for Tee and Strap Hinges?<\/h2>\n
\n
Benefits of BIS Certification<\/h2>\n
\n
BIS Certification for Tee and Strap Hinges \u2013 Quick Process<\/h2>\n
Why Choose Qualitance India?<\/h2>\n
\n
Frequently Asked Questions<\/h2>\n
1. What is BIS Certification for Tee and Strap Hinges?<\/h3>\n
2. Which standard applies to Tee and Strap Hinges?<\/h3>\n
3. Is BIS certification mandatory for Tee and Strap Hinges?<\/h3>\n
4. What certification scheme applies?<\/h3>\n
5. What is the current Product Manual?<\/h3>\n
6. What is the sample size?<\/h3>\n
7. What raw materials are specified?<\/h3>\n
\n
8. How are Tee Hinges classified?<\/h3>\n
\n
9. How are Strap Hinges classified?<\/h3>\n
\n
10. What is the main basis of product grouping?<\/h3>\n
11. How are sizes designated?<\/h3>\n
12. How are representative samples selected?<\/h3>\n
13. Can all hinge types be covered by one sample?<\/h3>\n
14. What are the major tests for Tee and Strap Hinges?<\/h3>\n
\n
15. Are dimensions and tolerances tested?<\/h3>\n
16. Are screw holes tested?<\/h3>\n
17. Are knuckles tested?<\/h3>\n
18. Is the hinge pin controlled?<\/h3>\n
19. Is workmanship tested?<\/h3>\n
20. Is finish tested?<\/h3>\n
21. Is packing tested?<\/h3>\n
22. Is marking tested?<\/h3>\n
23. What is the current BIS testing cost?<\/h3>\n
24. Does laboratory testing cost include BIS certification fees?<\/h3>\n
25. Is factory inspection required?<\/h3>\n
26. What documents are needed for BIS certification?<\/h3>\n
27. Can a manufacturer include both Tee and Strap Hinges?<\/h3>\n
28. Can all sizes be included in the licence?<\/h3>\n
29. What happens if the sample fails testing?<\/h3>\n
30. Can Qualitance India provide complete BIS consultancy?<\/h3>\n
Frequently Searched Topics<\/h2>\n
\n
Related BIS Certification Services<\/h2>\n
Contact Qualitance India<\/h2>\n
\nBIS Certification Consultancy for Manufacturers<\/p>\n
\nEmail:<\/strong> info@qualitanceindia.com<\/a>
\nWebsite:<\/strong> https:\/\/qualitanceindia.com\/<\/a><\/p>\nConclusion<\/h2>\n