A Tactical 3 Point Sling<\/strong> is a specialized textile product manufactured as a three-point support sling with textile, elastic, metallic and fastening components. Because the product needs consistent dimensional construction, suitable material properties, adequate strength and reliable workmanship, its raw materials and finished construction are important from a quality and conformity perspective.<\/p>\n In India, IS 16725:2018 \u2013 Textiles \u2013 Tactical 3 Points Sling Universal \u2013 Specification<\/strong> establishes the requirements for this product. The current BIS Product Manual PM\/16725\/1 dated February 2023<\/strong> states that certification is operated under Scheme-I of the BIS Conformity Assessment Regulations, 2018<\/strong> and identifies no amendments<\/strong>, no specific grouping guidelines<\/strong>, and a sample size of 10 slings made into one unit pack (bundle)<\/strong>.<\/p>\n IS 16725:2018 is included in the BIS compulsory certification framework under the Protective Textiles (Quality Control) Order, 2022<\/strong>. The Government order requires specified goods to conform to the relevant Indian Standard and bear the Standard Mark under a BIS licence according to Scheme-I. The original order also states that it does not apply to goods or articles meant for export.<\/p>\n BIS’s current Scheme-I listing continues to identify IS 16725:2018 \u2013 Tactical 3 point sling<\/strong> under the Protective Textiles category along with the applicable QCO framework and subsequent amendments.<\/p>\n The certification requirements are not limited to the finished sling. The BIS Product Manual specifies important requirements for the tape, shoulder pad, loops, metallic parts, sewing thread, stitching, dimensions, workmanship and finish. It also provides a detailed inspection and testing framework for ongoing production.<\/p>\n Qualitance India<\/strong> provides end-to-end BIS Certification Consultancy for Tactical 3 Point Sling as per IS 16725:2018<\/strong>, including product assessment, technical requirement review, documentation, raw-material conformity guidance, sample preparation, laboratory testing coordination, BIS application assistance, factory inspection preparation and quality-control documentation.<\/p>\n IS 16725:2018<\/strong> is titled:<\/p>\n \u201cTextiles \u2013 Tactical 3 Points Sling Universal \u2013 Specification.\u201d<\/strong><\/p>\n The standard is a product specification under the textiles sector. BIS’s Product Manual confirms that the certification operation is under Scheme-I<\/strong>, making the standard relevant to manufacturers seeking a BIS certification licence for the specified product.<\/p>\n The standard addresses important characteristics of the complete sling and its components, including:<\/p>\n The current Product Manual identifies NIL amendments<\/strong> and states that product grouping guidelines are Not Applicable<\/strong>.<\/p>\n A Tactical 3 Point Sling is a textile sling assembly consisting of multiple connected sections designed around a three-point configuration.<\/p>\n For certification purposes, the important consideration is not simply the appearance of the finished product but whether its materials, components, construction and finished workmanship comply with the requirements of IS 16725:2018<\/strong>.<\/p>\n The BIS Product Manual identifies several components, including:<\/p>\n Each component has specific material or performance requirements under the certification framework.<\/p>\n The BIS Product Manual identifies the product scope as:<\/p>\n Textiles \u2013 Tactical 3 points sling universal<\/strong><\/p>\n and provides the Standard Mark licence scope against IS 16725:2018.<\/p>\n The certification scope should be aligned with the actual manufactured product.<\/p>\n Before testing, manufacturers should verify:<\/p>\n Because the Product Manual states Grouping Guidelines: Not applicable<\/strong>, manufacturers should not assume that unrelated constructions or substantially different configurations can automatically be included under the same tested scope.<\/p>\n Yes, for covered products supplied in the Indian market under the applicable QCO framework.<\/strong><\/p>\n The Protective Textiles (Quality Control) Order, 2022<\/strong> specifically lists:<\/p>\n Tactical 3 point sling \u2013 IS 16725:2018<\/strong><\/p>\n The Order requires the specified goods to conform to the relevant Indian Standard and bear the Standard Mark under a BIS licence in accordance with Scheme-I<\/strong>. It also identifies BIS as the certifying and enforcing authority. Goods meant for export are outside the scope of the Order.<\/p>\n BIS’s current Scheme-I listing continues to show IS 16725:2018<\/strong> under the Protective Textiles category.<\/p>\n Manufacturers should therefore assess BIS applicability before manufacturing or supplying covered Tactical 3 Point Slings in India.<\/p>\n The Protective Textiles (Quality Control) Order, 2022<\/strong>, issued by the Ministry of Textiles, covers specified protective textile products.<\/p>\n The Schedule includes:<\/p>\n The current BIS Scheme-I page continues to associate IS 16725:2018 with the Protective Textiles QCO framework.<\/p>\n BIS Certification is the conformity assessment process through which a manufacturer demonstrates that the Tactical 3 Point Sling complies with the applicable requirements of IS 16725:2018.<\/p>\n The Product Manual states that the certification is operated under Scheme-I of the BIS Conformity Assessment Regulations, 2018<\/strong>.<\/p>\n After successful conformity assessment and grant of a BIS licence, the manufacturer can use the applicable BIS Standard Mark \/ ISI Mark<\/strong> on products covered by the approved licence and subject to the conditions of that licence.<\/p>\n The requirement is primarily relevant to manufacturers producing Tactical 3 Point Sling conforming to IS 16725:2018.<\/p>\n Potentially affected businesses include:<\/p>\n Importers, traders and sellers should independently verify the applicable regulatory position because BIS product certification under Scheme-I is granted to manufacturers within the prescribed conformity-assessment framework.<\/p>\n A manufacturer seeking BIS certification should maintain suitable manufacturing, inspection and quality-control facilities.<\/p>\n Depending on the production model, these may include:<\/p>\n The exact laboratory and testing arrangements should be established from the current BIS Product Manual and proposed product scope.<\/p>\n The first step is to assess whether the product falls within IS 16725:2018<\/strong>.<\/p>\n The review should cover:<\/p>\n The product is checked against the applicable material and construction requirements of the standard.<\/p>\n The exact product configuration to be included in the BIS licence is finalised.<\/p>\n The Product Manual identifies grouping as Not Applicable<\/strong>, so scope should be clearly established before testing.<\/p>\n The manufacturer identifies and documents the required materials and components.<\/p>\n Administrative, technical and quality-control documents are prepared.<\/p>\n The current Product Manual specifies:<\/p>\n Ten Tactical 3 Point Slings made into one unit pack (bundle).<\/strong><\/p>\n Representative samples are tested against the applicable requirements.<\/p>\n The manufacturer submits the application with the required documents and test information.<\/p>\n BIS evaluates the manufacturing, testing and quality-control arrangements.<\/p>\n Any observations identified during the assessment are addressed through corrective action.<\/p>\n After successful conformity assessment, BIS grants the licence for the approved product scope.<\/p>\n Conforming products covered by the licence can be marked according to the applicable BIS requirements.<\/p>\n The current Product Manual specifies:<\/p>\n Sample Size: Ten \u201cSling\u201d made into one unit pack (bundle).<\/strong><\/p>\n This sample requirement applies to the certification process as specified in the Product Manual.<\/p>\n Manufacturers should prepare the required sample quantity and ensure that the samples fully represent the construction intended for certification.<\/p>\n The BIS Product Manual gives detailed requirements for the raw materials and components.<\/p>\n The tape is required to be manufactured using:<\/p>\n Continuous filament yarn of Nylon 6 6<\/strong><\/p>\n and produced on a needle loom according to the specified weave particulars.<\/p>\n The shoulder pad contains:<\/p>\n The Product Manual specifies the middle rubber layer as:<\/p>\n 40 mm wide \u00d7 230 mm length \u00d7 3 mm thickness.<\/strong><\/p>\n The woven elastic tape used in the loops must meet the requirements of IS 9686<\/strong>, and its colour should match Component A.<\/p>\n The Product Manual identifies metallic components such as:<\/p>\n These are required to conform to IS 2062<\/strong>, except for shape and dimensions.<\/p>\n The Product Manual specifies Nylon sewing thread of green shade<\/strong>, matching Component A, conforming to Variety No. H1 of IS 4229<\/strong>.<\/p>\n The Product Manual permits conformity of raw materials to be established through:<\/p>\n This provision applies to the specified raw-material requirements under the Product Manual.<\/p>\n This makes proper supplier documentation and incoming-material control particularly important.<\/p>\n The testing programme covers both the complete product and its components.<\/p>\n Important characteristics include:<\/p>\n The current BIS laboratory database also shows detailed clause-wise testing entries for IS 16725:2018.<\/p>\n The nature of the filament used in the applicable textile components is verified through the relevant test methods.<\/p>\n The Product Manual references IS 667<\/strong> and identifies microscopic, dissolution, staining or melting-temperature approaches depending on the applicable method.<\/p>\n The denier of yarn is one of the specified characteristics under the tape construction requirements.<\/p>\n The Product Manual identifies equipment such as:<\/p>\n for the applicable determination.<\/p>\n Tenacity is an important yarn characteristic because it contributes to the strength of the textile components.<\/p>\n The Product Manual identifies a tensile testing machine<\/strong> with suitable clamps and pretensioning arrangements for the applicable test.<\/p>\n The tape and applicable woven components are evaluated for the number of ends and picks.<\/p>\n The Product Manual identifies a thread counter equipped with a microscope and graduated base for this purpose.<\/p>\n Tape width is a specified characteristic under the requirements for Component A.<\/p>\n The manufacturer needs appropriate dimensional control and inspection during production.<\/p>\n Mass per linear metre of tape is another important requirement.<\/p>\n The Product Manual identifies a conditioning chamber, tensile-testing machine and weighing balance for the test. The chamber condition specified is:<\/p>\n 65 \u00b1 2 percent relative humidity and 27 \u00b1 2\u00b0C.<\/strong><\/p>\n Breaking strength is tested for the relevant tape and component materials.<\/p>\n The current BIS Product Manual identifies the applicable tensile testing machine for breaking-strength determination.<\/p>\n Colour fastness to light is evaluated according to the applicable textile test method.<\/p>\n The Product Manual references IS\/ISO 105-B02:2014<\/strong> for artificial-light testing and identifies equipment such as a xenon arc light source, humidity chamber, black-standard thermometer and assessment cabinet.<\/p>\n Both:<\/p>\n are covered.<\/p>\n The Product Manual refers to IS\/ISO 105-X12<\/strong> and identifies suitable rubbing-test equipment and grey scales.<\/p>\n Colour fastness to washing includes:<\/p>\n The Product Manual refers to IS\/ISO 105-C10<\/strong> and specifies relevant washing-test equipment.<\/p>\n Dimensional change due to relaxation is evaluated in both directions as applicable.<\/p>\n The Product Manual references IS 10099:1982<\/strong> for the applicable apparatus arrangement.<\/p>\n The pH value of the aqueous extract is tested by the cold method.<\/p>\n The Product Manual references IS 1390<\/strong> and identifies:<\/p>\n for the testing arrangement.<\/p>\n The shoulder pad is an important component and has separate construction and material requirements.<\/p>\n The Product Manual identifies a top layer made from Nylon 6 6 fabric and a bottom layer based on Nylon tape.<\/p>\n The applicable checks include:<\/p>\n The top layer is identified as disruptive printed<\/strong> Nylon 6 6 fabric with specified weave construction.<\/p>\n Applicable characteristics include:<\/p>\n The bottom layer is identified as:<\/p>\n Nylon tape \u2013 50 mm wide<\/strong><\/p>\n and is subject to requirements including:<\/p>\n The woven elastic tape used in the loops is treated as Component D<\/strong>.<\/p>\n The Product Manual requires the material to comply with IS 9686<\/strong> and states that the colour of the elastic tape should match Component A.<\/p>\n The metallic parts of the sling include the listed buckles, D-rings and hook.<\/p>\n The Product Manual requires these metallic parts to conform to IS 2062<\/strong>, except for their shape and dimensions.<\/p>\n Conformity can be established through the permissible material-control arrangements.<\/p>\n Stitching is a specific requirement under Clause 4.1.<\/p>\n The Product Manual requires routine control of stitching and states that the manufacturer should maintain adequate inspection and in-process controls to ensure conformity.<\/p>\n Proper stitching control is important for maintaining consistent workmanship and assembly quality.<\/p>\n The sewing thread must conform to the applicable requirement of IS 4229<\/strong>.<\/p>\n The Product Manual identifies the specified H1 variety<\/strong> and allows conformity through supplier certificates, third-party reports, accredited laboratory reports or permitted in-house testing.<\/p>\n Workmanship and finish are important parts of final product conformity.<\/p>\n The BIS Product Manual requires manufacturers to maintain appropriate inspection and in-process controls to ensure that the product meets the applicable requirements.<\/p>\n Final products should therefore be checked for:<\/p>\n The current Product Manual provides an indicative list of major test equipment.<\/p>\n Depending on the testing scope, facilities may include:<\/p>\n The Product Manual clearly states that the equipment list is indicative and should not be treated as exhaustive<\/strong>.<\/p>\n The Product Manual requires a laboratory to be maintained that is suitably equipped and staffed for applicable tests. It also requires the manufacturer to prepare and implement a calibration plan<\/strong> for testing equipment and maintain test records.<\/p>\n This means manufacturers should have a systematic system for:<\/p>\n The BIS Product Manual provides a detailed inspection and testing scheme.<\/p>\n The manufacturer is required to maintain a suitable laboratory, implement calibration, maintain test records and control production covered by the licence.<\/p>\n The Product Manual identifies test equipment as either:<\/p>\n R \u2013 Required<\/strong><\/p>\n or<\/p>\n S \u2013 Subcontracting permitted<\/strong><\/p>\n for the applicable test requirements.<\/p>\n Subcontracting, where permitted, may be carried out through a laboratory recognized by BIS or an applicable Government laboratory empanelled by BIS under the provisions stated in the Product Manual.<\/p>\n The Product Manual defines the control unit as:<\/p>\n The entire quantity of slings manufactured from the same raw materials under similar conditions in a day.<\/strong><\/p>\n This definition is important for production control and routine testing.<\/p>\n Manufacturers should maintain clear batch or daily production records linking:<\/p>\n The Product Manual specifies regular controls for the tape used as Component A.<\/p>\n Examples include:<\/p>\n One sample from each consignment.<\/p>\n One sample from each control unit.<\/p>\n One sample from each control unit.<\/p>\n One sample from each control unit.<\/p>\n Once a year, and also when the supplier or colour changes.<\/p>\n Once a week.<\/p>\n Once a week.<\/p>\n Once a week.<\/p>\n Once a week.<\/p>\n For the shoulder-pad top layer, the Product Manual specifies controls for:<\/p>\n Several of the characteristics are controlled each consignment or each control unit, while colour fastness to light is listed once annually and when the supplier or colour changes.<\/p>\n For the 50 mm-wide Nylon tape forming the bottom layer, the Product Manual identifies:<\/p>\n The Product Manual places responsibility on the manufacturer to maintain appropriate inspection and in-process controls for the dimensions and construction of the sling and its components.<\/p>\n Dimensional inspection can involve:<\/p>\n Suitable measuring instruments should be maintained under calibration control.<\/p>\n Manufacturers should establish a controlled procurement system.<\/p>\n Important records include:<\/p>\n This is especially important because the Product Manual allows certain raw-material conformity to be established through supplier certificates or other permitted evidence.<\/p>\n A typical manufacturing process may include:<\/p>\n The actual production process may differ according to the manufacturer’s technology and production setup.<\/p>\n The Product Manual identifies IS 15570<\/strong> for dyes used for dyeing and printing. The specified control requires dyes to meet the applicable requirement relating to banned amines.<\/p>\n Manufacturers should therefore maintain appropriate supplier and material records for dyed and printed materials.<\/p>\n For IS 16725:2018, the current Product Manual states:<\/p>\n Grouping Guidelines: Not Applicable.<\/strong><\/p>\n This means manufacturers should clearly define the product configuration they intend to include in the BIS licence and should not rely on assumed grouping arrangements.<\/p>\n Where multiple configurations exist, a technical review should be conducted before selecting samples.<\/p>\n Factory assessment is an important stage of BIS certification.<\/p>\n During the assessment, BIS may review:<\/p>\n Identification, storage and traceability of textile and component materials.<\/p>\n Production of the required tape and its construction.<\/p>\n Control over the layers and specified material construction.<\/p>\n Accuracy of cutting and quality of stitching.<\/p>\n Proper assembly of buckles, D-rings, hooks and other components.<\/p>\n Availability of required testing facilities or permitted testing arrangements.<\/p>\n Calibration records for testing and measuring equipment.<\/p>\n Incoming, in-process and final inspection systems.<\/p>\n Daily production and control-unit records.<\/p>\n Records demonstrating conformity.<\/p>\n Correct Standard Mark and packing arrangements.<\/p>\n A manufacturer should generally prepare documents such as:<\/p>\n The exact documentation depends on the manufacturing arrangement and proposed licence scope.<\/p>\n The Product Manual provides specific requirements for Standard Marking.<\/p>\n It states that the Standard Mark<\/strong> from the licence schedule must be incorporated legibly and indelibly on each sling, provided that the marked material conforms to every requirement of the specification.<\/p>\n Each bundle and bale containing slings must also be marked with:<\/p>\nWhat is IS 16725:2018?<\/h2>\n
\n
What is a Tactical 3 Point Sling?<\/h2>\n
\n
Scope of IS 16725:2018<\/h2>\n
\n
Is BIS Certification Mandatory for Tactical 3 Point Sling?<\/h2>\n
Protective Textiles Quality Control Order<\/h2>\n
\n\n
\n Product<\/th>\n Indian Standard<\/th>\n<\/tr>\n \n Protective clothing for firefighters<\/td>\n IS 16890:2018<\/td>\n<\/tr>\n \n Protective gloves for firefighters<\/td>\n IS 16874:2018<\/td>\n<\/tr>\n \n Protective clothing for industrial workers exposed to heat<\/td>\n IS 15748:2022<\/td>\n<\/tr>\n \n High visibility warning clothes<\/td>\n IS 15809:2017<\/td>\n<\/tr>\n \n Protective clothing for welding<\/td>\n IS 16655:2017<\/td>\n<\/tr>\n \n Tactical 3 point sling<\/strong><\/td>\n IS 16725:2018<\/strong><\/td>\n<\/tr>\n \n Pouch for ammunition and grenades<\/td>\n IS 16726:2018<\/td>\n<\/tr>\n \n Bullet resistant jackets<\/td>\n IS 17051:2018<\/td>\n<\/tr>\n \n Water-proof multipurpose rain poncho<\/td>\n IS 17286:2019<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n BIS Certification for Tactical 3 Point Sling<\/h2>\n
Who Needs BIS Certification for Tactical 3 Point Sling?<\/h2>\n
\n
BIS Certification Eligibility Requirements<\/h2>\n
\n
BIS Certification Process for Tactical 3 Point Sling<\/h2>\n
Step 1 \u2013 Product Applicability Assessment<\/h2>\n
\n
Step 2 \u2013 Technical Requirement Review<\/h2>\n
Step 3 \u2013 Product Scope Finalisation<\/h2>\n
Step 4 \u2013 Raw Material Assessment<\/h2>\n
Step 5 \u2013 Documentation Preparation<\/h2>\n
Step 6 \u2013 Sample Preparation<\/h2>\n
Step 7 \u2013 Laboratory Testing<\/h2>\n
Step 8 \u2013 BIS Application<\/h2>\n
Step 9 \u2013 Factory Assessment<\/h2>\n
Step 10 \u2013 Observation Closure<\/h2>\n
Step 11 \u2013 BIS Licence Grant<\/h2>\n
Step 12 \u2013 Standard Marking<\/h2>\n
BIS Sample Requirement for Tactical 3 Point Sling<\/h2>\n
Raw Materials Used in Tactical 3 Point Sling<\/h2>\n
Component A \u2013 Tape<\/h2>\n
Component B \u2013 Shoulder Pad<\/h2>\n
\n
Component D \u2013 Loops<\/h2>\n
Metallic Parts<\/h2>\n
\n
Sewing Thread<\/h2>\n
Raw Material Conformity<\/h2>\n
\n
Testing Requirements for IS 16725:2018<\/h2>\n
\n
Nature of Filament<\/h2>\n
Yarn Denier<\/h2>\n
\n
Tenacity of Single-Ply Yarn<\/h2>\n
Number of Ends and Picks<\/h2>\n
Width of Tape<\/h2>\n
Mass per Linear Metre<\/h2>\n
Breaking Strength<\/h2>\n
Colour Fastness to Light<\/h2>\n
Colour Fastness to Rubbing<\/h2>\n
\n
Colour Fastness to Washing<\/h2>\n
\n
Dimensional Change Due to Relaxation<\/h2>\n
pH Value of Aqueous Extract<\/h2>\n
\n
Shoulder Pad Requirements<\/h2>\n
\n
Shoulder Pad Top Layer<\/h2>\n
\n
Shoulder Pad Bottom Layer<\/h2>\n
\n
Elastic Tape Used in Loops<\/h2>\n
Metallic Parts<\/h2>\n
Stitching Requirements<\/h2>\n
Sewing Thread<\/h2>\n
Workmanship and Finish<\/h2>\n
\n
Testing Equipment for IS 16725:2018<\/h2>\n
\n
Testing in Factory Laboratory<\/h2>\n
\n
Scheme of Inspection and Testing<\/h2>\n
Control Unit for Tactical 3 Point Sling<\/h2>\n
\n
Routine Control of Tape<\/h2>\n
Nature of Filament<\/h3>\n
Width<\/h3>\n
Mass per Linear Metre<\/h3>\n
Breaking Strength<\/h3>\n
Colour Fastness to Light<\/h3>\n
Colour Fastness to Rubbing<\/h3>\n
Colour Fastness to Washing<\/h3>\n
Dimensional Change<\/h3>\n
pH<\/h3>\n
Routine Control of Shoulder Pad<\/h2>\n
\n
Routine Control of Bottom Shoulder-Pad Layer<\/h2>\n
\n
Dimensions and Construction<\/h2>\n
\n
Raw Material Procurement<\/h2>\n
\n
Manufacturing Process for Tactical 3 Point Sling<\/h2>\n
\n
Dyeing and Printing Requirements<\/h2>\n
Product Grouping<\/h2>\n
Factory Inspection for BIS Certification<\/h2>\n
Raw Material Area<\/h3>\n
Tape Manufacturing<\/h3>\n
Shoulder Pad Manufacturing<\/h3>\n
Cutting and Sewing<\/h3>\n
Component Assembly<\/h3>\n
Testing Laboratory<\/h3>\n
Calibration<\/h3>\n
Quality Control<\/h3>\n
Production Records<\/h3>\n
Test Records<\/h3>\n
Packing and Marking<\/h3>\n
Documents Required for BIS Certification<\/h2>\n
\n
Packing and Marking Requirements<\/h2>\n