Latest Updates

NABL Accreditation Process: Steps, Documents and Preparation (ISO/IEC 17025)

  • Home
  • Blogs
  • NABL Accreditation Process: Steps, Documents and Preparation (ISO/IEC…
NABL Accreditation Process: Steps, Documents and Preparation (ISO/IEC 17025)

NABL Accreditation Process: Steps, Documents and Preparation (ISO/IEC 17025)

Quick answer: NABL accreditation confirms that a testing or calibration laboratory is technically competent under ISO/IEC 17025. The lab sets up an ISO/IEC 17025 management system, applies online to NABL, goes through document review, an optional pre-assessment and an on-site final assessment, closes any non-conformities and is then granted accreditation, valid for four years.

NABL (National Accreditation Board for Testing and Calibration Laboratories) accreditation is the most widely accepted proof of a laboratory’s competence in India. This guide walks through the NABL accreditation process, the preparation it needs and the points where most labs lose time.

NABL / ISO/IEC 17025 accreditation for laboratories

Who should apply for NABL accreditation?

  • Testing laboratories – chemical, mechanical, electrical, electronics, food, water, environmental, textile and more
  • Calibration laboratories
  • In-house quality control labs of manufacturers
  • Labs that want to be recognised by BIS under the Laboratory Recognition Scheme
  • Government, PSU and third-party commercial labs

Before you apply: getting ready

Most of the work happens before the application. A lab is ready when it has:

  • A documented management system meeting ISO/IEC 17025:2017 (quality manual, procedures and records)
  • Defined scope – the tests or calibrations, methods, ranges and measurement uncertainty
  • Trained and authorised staff for each test
  • Calibrated equipment with metrological traceability
  • Method validation or verification records
  • Participation in proficiency testing or inter-laboratory comparisons
  • At least one completed internal audit and management review

NABL accreditation process: step by step

NABL accreditation process in 6 steps
NABL accreditation process at a glance
  1. Online application. The lab applies on the NABL portal with its scope, quality manual and fees.
  2. Acknowledgement and scrutiny. NABL checks that the application is complete.
  3. Document review. An assessor reviews the management system documents against ISO/IEC 17025. NABL informs the lab of any inadequacies, and the lab corrects its documents within the time NABL allows.
  4. Pre-assessment (if conducted). A visit to check the lab’s readiness and plan the final assessment.
  5. Final assessment. An assessment team of a lead assessor and technical assessors visits the lab, witnesses tests and reviews records for every parameter in the scope.
  6. Corrective actions. The lab closes the non-conformities raised during the assessment and submits evidence.
  7. Review and decision. NABL reviews the assessment report and corrective actions and decides on accreditation.
  8. Grant of accreditation. The lab receives its certificate and scope of accreditation.

After accreditation

NABL accreditation is valid for four years. During this period NABL carries out surveillance, and the lab must keep taking part in proficiency testing, run internal audits and management reviews, and inform NABL of major changes. Labs should apply for reassessment well before the accreditation expires.

Where labs usually lose time

  • Scope that is too broad for the lab’s actual equipment and staff
  • Missing measurement uncertainty or method validation records
  • Equipment calibration that is not traceable or has expired
  • No proficiency testing for some parameters
  • Staff who cannot explain the procedures they follow during the witness test

Frequently Asked Questions

Is NABL accreditation mandatory?

NABL accreditation is voluntary. However, many regulators, tenders and certification schemes require it, and it is a prerequisite for BIS laboratory recognition.

How long is NABL accreditation valid?

NABL accreditation is valid for four years, with surveillance assessments during the cycle.

Is a pre-assessment compulsory?

No. After the document review, NABL may conduct a pre-assessment to check readiness. It is a useful dry run before the final assessment.

Can our consultant be present during the NABL assessment?

No. NABL officials and the assessment team interact only with the laboratory’s own staff during document review and assessment. Your consultant’s role is to prepare the team beforehand.

Which standard does NABL use for testing and calibration labs?

Testing and calibration laboratories are accredited to ISO/IEC 17025:2017. Medical labs are accredited to ISO 15189.

HS

Written by

BIS Certification Consultant, Qualitance India · 10+ years experience · 200+ products certified

Last updated: November 2026

Need help with BIS certification for this product?

Get a free consultation from our compliance experts — we handle testing, documentation and the complete BIS process for you.

Get Free Consultation +91 93106 15170
Free PDF Download

BIS Certification Readiness Checklist 2026

  • Documents, testing & factory requirements in one place
  • Covers ISI Mark, CRS, FMCS & Hallmarking
  • Tick-box format — share it with your team

Talk to us?