Partner Us

BIS Certification for Gypsum Plaster Boards – Coated/Laminated | IS 2095 (Part 2):2022 – Qualitance India

BIS Certification for Gypsum Plaster Boards – Coated/Laminated | IS 2095 (Part 2):2022 – Qualitance India

BIS Certification for Coated/Laminated Gypsum Plaster Boards – IS 2095 (Part 2):2022

Coated and laminated gypsum plaster boards are widely used for interior walls, ceilings, partitions and decorative finishes in residential, commercial and institutional buildings. These boards combine a gypsum-based core with a coating or laminated surface, such as paper, plastic film or wood veneer, depending on the product design. For manufacturers supplying these products in India, IS 2095 (Part 2):2022 – Gypsum Plaster Boards: Specification, Part 2: Coated/Laminated Gypsum Plaster Boards is the relevant Indian Standard. BIS lists this standard under its Scheme-I (ISI Mark Scheme) category for gypsum-based building materials. <Cite refs={["turn972691search0","turn455245view0"]}/> Qualitance India supports manufacturers with BIS certification consultancy, technical documentation, testing coordination and factory-readiness preparation.

1. What Is IS 2095 (Part 2):2022?

IS 2095 (Part 2):2022 specifies requirements for coated or laminated gypsum plaster boards. It is the third revision of the standard, according to BIS's standard information. <Cite refs={["turn972691search3","turn972691search26"]}/> The standard addresses important product characteristics, including:
  • Raw materials used in board manufacture.
  • Board dimensions and dimensional tolerances.
  • Finish and surface quality.
  • Density.
  • Flexural breaking load.
  • Fire resistance.
  • Marking and other applicable product requirements.
The standard should be read alongside the current BIS product manual, which describes the sampling approach, product grouping, equipment and factory inspection and testing requirements. <Cite refs={["turn455245view0"]}/>

2. Is BIS Certification Mandatory for Coated/Laminated Gypsum Boards?

BIS lists IS 2095 (Part 2):2022 under the Gypsum Based Building Materials (Quality Control) Order, 2024, notified through S.O. 1153(E), dated 6 March 2024, along with subsequent corrigendum and amendment references. <Cite refs={["turn972691search0","turn972691search22"]}/> Where the QCO applies, the product must comply with the applicable conformity requirements and Standard Mark provisions, subject to the exact terms of the order and any valid exemptions. Manufacturers and importers should verify the latest regulatory position before placing the product on the Indian market. Key checks include:
  • Whether the product is covered by IS 2095 (Part 2):2022.
  • Whether the QCO applies to the proposed manufacturing, import or supply activity.
  • Whether any specific exemption applies to the business or transaction.
  • Whether amendments or government orders have changed the applicable requirements.
  • Whether the proposed product type and coating or laminating material fall within the intended licence scope.
BIS's product listing also references orders dated 13 February 2026 concerning exemptions against import and purchase for the gypsum-based building materials category. These orders must be examined for their exact scope; they should not be interpreted as a blanket exemption for every manufacturer or product. <Cite refs={["turn972691search0"]}/>

3. Product Scope and Board Types

The BIS product manual identifies the licence scope through the following parameters:
  • Product: Coated/Laminated Gypsum Plaster Board.
  • Size: The approved board dimensions.
  • Type of gypsum board: The relevant board type.
  • Laminating/coating material: The material used for the finished surface. <Cite refs={["turn455245view0"]}/>
The product manual provides the following examples of dimensions and coating materials:
Parameter Examples in the BIS product manual
Width 600 mm and 1,220 mm
Length 1,800 mm to 3,600 mm
Thickness 9.5 mm, 12.5 mm and 15 mm
Coating/laminating material Wood veneer, plastic film, paper and similar materials
The manual notes that other dimensions may be manufactured by mutual agreement between the purchaser and manufacturer, subject to the applicable tolerances. <Cite refs={["turn455245view0"]}/> These are examples in the product manual, not a substitute for confirming the actual product scope. Manufacturers should prepare a list of all board sizes, types, thicknesses and coating materials proposed for certification.

4. BIS Grouping Guidelines for Licence Scope

Product grouping is important because a manufacturer may produce multiple board sizes, thicknesses, types and finishes. According to Annex A of the BIS product manual:
  • Each board type, thickness and laminating/coating material must be tested for all applicable requirements to cover that particular combination in the licence scope.
  • A board of any width and the highest length may be tested to cover widths and lengths up to and including the tested length, subject to the manual's grouping guidelines.
  • The licence scope may be restricted based on the manufacturer's manufacturing and testing capabilities. <Cite refs={["turn455245view0"]}/>
Before applying, manufacturers should prepare a product matrix covering:
  1. Board type.
  2. Thickness.
  3. Width and length.
  4. Coating or laminating material.
  5. Required testing for each proposed combination.
The final grouping and testing plan should be confirmed against the current BIS product manual and instructions from the relevant BIS office.

5. Raw Materials Required for Coated/Laminated Gypsum Boards

The BIS product manual identifies the following raw-material categories for the certification process:
  • Gypsum plaster — Clause 4.1.
  • Fibres — Clause 4.2.
  • Additives — Clause 4.3.
  • Laminating/coating material — Clause 4.4. <Cite refs={["turn455245view0"]}/>
Manufacturers should maintain suitable purchasing, inspection and traceability records for these materials. A practical raw-material document set may include:
  • Raw-material specifications.
  • Supplier and purchase records.
  • Material test certificates, where applicable.
  • Incoming-material inspection records.
  • Batch or lot identification.
  • Records of material acceptance and rejection.
  • Details of coating or laminating materials used in each product variant.
The applicable clauses of IS 2095 (Part 2):2022 should be consulted to establish the precise material requirements.

6. BIS Testing Requirements for IS 2095 (Part 2):2022

Testing helps establish that coated or laminated gypsum plaster boards conform to the requirements of the Indian Standard. The BIS product manual identifies the following principal requirements and related test equipment. <Cite refs={["turn455245view0"]}/>

6.1 Dimensions and tolerances

Dimensional inspection checks the board's length, width and thickness against the applicable requirements. The product manual identifies measuring tapes, steel scales, micrometers, straightness edges and squareness edges among the equipment used for dimensional checks.

6.2 Finish

Finish inspection evaluates the surface and workmanship against the applicable standard requirements. The manufacturer should maintain appropriate in-process inspection controls and records.

6.3 Density

Density testing evaluates the density of the board using the applicable test method and equipment.

6.4 Flexural breaking load

Flexural breaking load testing evaluates the board's resistance to bending under the prescribed test conditions. The product manual states that flexural breaking load requirements depend on board thickness. <Cite refs={["turn455245view0"]}/>

6.5 Fire resistance

Fire resistance is included as a requirement in the product manual. The manual identifies the relevant test equipment and a testing frequency in its Scheme of Inspection and Testing. The specific test method, acceptance criteria, frequency and permitted testing arrangements should be confirmed from the applicable standard and current BIS documents.

6.6 Raw-material conformity

The product manual also identifies checks for gypsum plaster and refers to the relevant material requirements in Clause 4.1. The manufacturer should maintain appropriate records and follow the inspection and testing scheme. <Cite refs={["turn455245view0"]}/>

7. Sample Quantity for BIS Certification

The BIS product manual PM/IS 2095 (Part 2)/1/Feb 23 specifies the sample size as: Four full-size gypsum plaster boards. <Cite refs={["turn455245view0"]}/> Before arranging samples, manufacturers should confirm:
  • The board type to be assessed.
  • The thickness and dimensions of the samples.
  • The coating or laminating material.
  • The tests required for the proposed licence scope.
  • The current sampling and grouping instructions.
Because each type, thickness and coating/laminating material combination has specific coverage implications, manufacturers should coordinate the sample plan before sending boards for testing. <Cite refs={["turn455245view0"]}/>

8. Factory and Laboratory Requirements

The BIS product manual requires the manufacturer to maintain a suitably equipped and staffed laboratory for the tests specified in the applicable inspection and testing scheme. It also requires a calibration plan for test equipment and records of tests carried out to establish conformity. <Cite refs={["turn455245view0"]}/> A factory-readiness review should cover:
  • Manufacturing equipment and process controls.
  • Measuring instruments and test equipment.
  • Calibration and maintenance records.
  • Trained personnel responsible for testing.
  • Raw-material inspection and traceability.
  • In-process and finished-product inspection.
  • Product identification and control-unit records.
  • Handling of nonconforming boards.
  • Fire-resistance testing arrangements.
The BIS manual permits subcontracting for specified tests to a BIS-recognised laboratory or a government laboratory empanelled by BIS, as described in its inspection and testing scheme. Manufacturers should verify the current requirements before relying on external testing. <Cite refs={["turn455245view0"]}/>

9. Factory Inspection and Control Unit

The BIS product manual defines a control unit as gypsum boards of the same type, size and laminating/coating material produced in a day from similar raw materials under similar production conditions. <Cite refs={["turn455245view0"]}/> The manual's inspection and testing scheme includes:
  • Finish inspection through appropriate in-process controls.
  • Dimensional checks.
  • Density testing.
  • Flexural breaking load testing.
  • Fire-resistance testing at the specified frequency.
  • Maintenance of test records and calibration arrangements. <Cite refs={["turn455245view0"]}/>
The manual indicates that density and flexural breaking load tests are conducted for each control unit, while fire-resistance testing is identified at a frequency of once every six months. The exact implementation should be confirmed against the latest applicable BIS requirements. <Cite refs={["turn455245view0"]}/>

10. Documents Required for BIS Certification

The following checklist can help manufacturers prepare for the application. The final list must be confirmed against the current BIS application process.

A. Business and factory documents

  • Legal name and constitution of the business.
  • Factory address and applicable occupancy or ownership documents.
  • GST registration and other relevant business registrations.
  • Authorised signatory details and authorisation documents.
  • Factory layout and manufacturing facility details.
  • Manufacturing process flow chart.

B. Product and technical documents

  • Product description and intended application.
  • Board type and proposed product range.
  • Board sizes, thicknesses and coating/laminating materials.
  • Technical drawings and product specifications.
  • Raw-material specifications and supplier details.
  • Proposed product marking and identification information.

C. Quality-control and testing documents

  • List of manufacturing and testing equipment.
  • Calibration certificates and maintenance records.
  • Raw-material inspection procedures.
  • In-process and finished-product inspection procedures.
  • Test formats and available internal test records.
  • Product traceability and control-unit records.
  • Records of rejected boards and corrective actions.
  • Details of personnel responsible for testing and quality control.

D. Application-related documents

  • Current BIS application forms and declarations.
  • Manufacturing-unit and proposed licence-scope details.
  • Required fee payments and supporting information.
  • Additional documents requested during application scrutiny or factory assessment.
This is a preparation checklist, not a replacement for the official BIS application requirements.

11. BIS Certification Process for IS 2095 (Part 2):2022

The following is a general preparation workflow. The exact procedure should be confirmed against the current BIS requirements. Step 1: Confirm the applicable standard and QCO Verify the product's applicability to IS 2095 (Part 2):2022 and check the current QCO, amendments and any applicable exemptions. Step 2: Define the product scope Prepare a detailed list of board types, dimensions, thicknesses and coating/laminating materials. Step 3: Review the factory and testing facilities Assess manufacturing controls, laboratory capability, calibration, raw-material inspection and quality-control documentation. Step 4: Prepare the application documents Compile business, factory, product, technical and testing records required by BIS. Step 5: Arrange samples and testing Confirm the required sample size, grouping guidelines and testing requirements. The product manual specifies four full-size boards for sampling. <Cite refs={["turn455245view0"]}/> Step 6: Complete the BIS assessment Address application scrutiny, factory assessment, testing and any observations or corrective actions required by BIS. Step 7: Obtain the licence before marking The manufacturer may use the Standard Mark only after the required BIS authorisation has been granted and in accordance with the licence conditions. Step 8: Maintain ongoing conformity Continue the required production controls, inspection, testing, calibration and recordkeeping to maintain conformity with the applicable standard and licence conditions.

12. BIS Certification Fees and Testing Costs

The overall certification budget depends on the current BIS fee schedule, testing scope, product variants and factory readiness. Potential cost components include:
  • BIS application and licence-related fees, as applicable.
  • Product testing charges.
  • Sample preparation and transportation.
  • Testing equipment and calibration.
  • Quality-control documentation and factory preparation.
  • Consultancy charges, if professional assistance is engaged.
BIS's LIMS lists an example testing charge of ₹40,000 excluding taxes for IS 2095 (Part 2):2022 at Atckon Laboratories LLP, Bahadurgarh, effective from 2 April 2026. The listing notes that fire resistance is excluded from this particular testing package. This is a laboratory-specific charge, not the total cost of obtaining BIS certification. <Cite refs={["turn455245view1"]}/> Other laboratories list different charges and test packages. The manufacturer should verify the current fee, included tests, exclusions and laboratory availability before finalising a budget.

13. How Long Does BIS Certification Take?

The certification timeline depends on the completeness of the application, factory readiness, testing availability, sample conformity, factory assessment and BIS processing. No single completion period can be guaranteed for every application. Delays may occur if:
  • The proposed product scope is incomplete.
  • Samples fail one or more requirements.
  • Required testing equipment or calibration is unavailable.
  • Documentation is incomplete.
  • The factory needs to address assessment observations.
  • Additional testing is needed for other board types or coating materials.
A realistic project schedule should be developed after reviewing the product range and the manufacturer's testing capability.

14. ECO Mark Option for Gypsum Boards

The BIS product manual states that, where a manufacturer opts for the ECO Mark, gypsum plaster boards must be manufactured using by-product gypsum and conform to Clause 8 of IS 2095 (Part 2):2022. <Cite refs={["turn455245view0"]}/> Manufacturers interested in the ECO Mark should confirm the current eligibility, documentation and verification requirements before including this option in their certification plan.

15. Common Challenges During BIS Certification

Manufacturers may experience delays or additional costs when:
  • The selected standard does not match the actual product.
  • Board types, sizes or coating materials are not clearly documented.
  • Samples do not represent the proposed licence scope.
  • Dimensional or finish controls are inadequate.
  • Required test equipment or calibration records are unavailable.
  • Density or flexural breaking load results do not meet the requirements.
  • Fire-resistance testing arrangements are not confirmed.
  • Production and control-unit records are incomplete.
A pre-application technical review can help identify these issues before formal assessment and testing.

16. Frequently Asked Questions

Q1. What is IS 2095 (Part 2):2022?

It is the Indian Standard for coated or laminated gypsum plaster boards, identified by BIS as the third revision of this part of the gypsum plaster board specification. <Cite refs={["turn972691search3"]}/>

Q2. Is BIS certification applicable to coated/laminated gypsum boards?

BIS lists IS 2095 (Part 2):2022 under the Gypsum Based Building Materials QCO 2024 category. Manufacturers should verify the current QCO and applicable exemptions for their specific product and transaction. <Cite refs={["turn972691search0"]}/>

Q3. How many samples are required?

The BIS product manual specifies four full-size gypsum plaster boards. Confirm the latest sampling instructions and the coverage needed for the proposed licence scope. <Cite refs={["turn455245view0"]}/>

Q4. Which board dimensions are listed in the product manual?

Examples include widths of 600 mm and 1,220 mm, lengths from 1,800 mm to 3,600 mm, and thicknesses of 9.5 mm, 12.5 mm and 15 mm. Other dimensions may be possible subject to the manual's conditions and applicable tolerances. <Cite refs={["turn455245view0"]}/>

Q5. Which tests are relevant to IS 2095 (Part 2):2022?

The product manual identifies dimensions, finish, density, flexural breaking load and fire resistance, along with applicable raw-material controls. <Cite refs={["turn455245view0"]}/>

Q6. What is the cost of BIS certification?

The total cost depends on current BIS fees, the selected testing package, product scope, factory readiness and other project-specific expenses. A laboratory testing charge alone does not represent the complete certification cost.

Q7. Can the ISI mark be used before the licence is granted?

No. The Standard Mark must be used only after the required BIS authorisation is granted and in accordance with the licence conditions.

Get BIS Certification Consultancy for IS 2095 (Part 2):2022

Planning to apply for BIS certification for coated or laminated gypsum plaster boards? Qualitance India can support your certification preparation through product-standard applicability review, documentation assistance, factory-readiness assessment, testing coordination and BIS application support. Our consultancy approach focuses on your actual product range, board dimensions, coating materials, manufacturing facilities and applicable regulatory requirements. Qualitance India – Improving Quality & Competence Contact us to discuss your board specifications, factory facilities and BIS certification requirements.

Official References

  1. BIS Product Manual – IS 2095 (Part 2):2022
  2. BIS – Scheme-I (ISI Mark Scheme)
  3. BIS – Laboratory Information Management System
  4. BIS – Standard Details
Regulatory note: Indian Standards, amendments, QCOs, exemptions, laboratory charges and application procedures may change. Verify the latest official BIS requirements before making certification or market-placement decisions.

Talk to us?