BIS Certification for Cold-Rolled Stainless Steel Strips for Razor Blades | IS 9294:1979 – Qualitance India
BIS Certification for Cold-Rolled Stainless Steel Strips for Razor Blades
Cold-rolled stainless steel strips are an important raw material in the manufacturing of razor blades. These strips must possess carefully controlled chemical composition, hardness, microstructure, carbide density, dimensional accuracy and surface finish to ensure that the finished blades achieve the required cutting performance and durability.
To establish quality requirements for this specialised material, the Bureau of Indian Standards (BIS) has published IS 9294:2023 – Cold-Rolled Stainless Steel Strips for Razor Blades.
The standard specifies requirements for cold-rolled stainless steel strips used in razor blade manufacturing, including material composition, hardness, microstructure, carbide density, dimensions, tolerances and surface finish.
Manufacturers and importers supplying this product in India must also consider the applicable Steel and Steel Products Quality Control Order (QCO) and BIS certification requirements.
This article explains the current standard, regulatory position, product scope, technical requirements, testing parameters, sample requirements, grouping guidelines, documents and BIS certification process.
1. What is IS 9294?
IS 9294 is the Indian Standard titled:
Cold-Rolled Stainless Steel Strips for Razor Blades – Specification.
The earlier edition was IS 9294:1979. BIS subsequently revised the standard and published:
IS 9294:2023 – Cold-Rolled Stainless Steel Strips for Razor Blades (First Revision).
The revised standard became applicable from 3 February 2024, and the earlier 1979 edition was withdrawn on the same date.
The standard covers cold-rolled stainless steel strips intended for manufacturing razor blades.
These strips require specific material characteristics because razor blade production involves precision processing, heat treatment, grinding and edge formation.
The standard addresses important product characteristics, including:
- Chemical composition
- Hardness
- Microstructure
- Carbide density
- Edge condition
- Dimensions and tolerances
- Surface finish
2. Important Update: IS 9294:1979 Replaced by IS 9294:2023
Manufacturers searching for BIS certification under IS 9294 should note that the 1979 edition is no longer the current standard.
| Particular | Details |
|---|---|
| Earlier standard | IS 9294:1979 |
| Earlier title | Cold-Rolled Stainless Steel Strips for Razor Blades |
| Revised standard | IS 9294:2023 |
| Current title | Cold-Rolled Stainless Steel Strips for Razor Blades – Specification |
| Revision | First Revision |
| Publication date | 3 August 2023 |
| Withdrawal of old edition | 3 February 2024 |
| Current grade | X66Cr13 |
| Certification framework | BIS Scheme-I |
BIS issued implementation guidelines through Circular CMD-2/16:9294 dated 22 November 2023.
The guidelines required existing licensees to implement the revised standard by 3 February 2024. New applications could not be granted under the old edition after that date.
Major changes introduced in IS 9294:2023
BIS identified the following important changes in the revised standard:
- Modification of the clause relating to supply of materials.
- Changes in the recommended load for hardness testing and specified hardness values.
- Modification of carbide density requirements.
- Introduction of a separate sampling clause.
- Modification of dimensional and tolerance requirements.
- Modification of surface finish requirements, including specified surface roughness values.
Manufacturers must therefore use IS 9294:2023 and the revised product manual rather than relying on the earlier 1979 edition.
3. Is BIS Certification Mandatory for Cold-Rolled Stainless Steel Strips for Razor Blades?
<badge color=”success”>Covered under Steel QCO</badge>
Yes. Cold-Rolled Stainless Steel Strips for Razor Blades are included in the Ministry of Steel’s Steel and Steel Products (Quality Control) Order, 2024.
The applicable regulatory details are:
| Particular | Details |
|---|---|
| Product | Cold-Rolled Stainless Steel Strips for Razor Blades |
| Current Indian Standard | IS 9294:2023 |
| Earlier QCO reference | IS 9294:1979 |
| QCO | Steel and Steel Products (Quality Control) Order, 2024 |
| Notification | S.O. 3716(E), dated 29 August 2024 |
| Schedule | Schedule 1, Serial No. 93 |
| Original implementation | With immediate effect |
| Certification scheme | BIS Scheme-I |
| Certification mark | ISI Standard Mark |
| Certifying authority | Bureau of Indian Standards |
Applicable ITC (HS) Codes
The 2024 QCO entry identifies the following ITC (HS) codes:
- 72202021
- 72202022
- 72202029
- 72202090
- 72209021
- 72209022
- 72209029
- 72209090
The applicable classification should be verified against the actual product and current customs tariff.
Does the QCO continue to apply after the standard revision?
Yes, the QCO framework includes a provision for amendments or revisions to the Indian Standards listed in its Schedule.
The revised IS 9294:2023 was implemented by BIS from 3 February 2024. The 2024 QCO subsequently listed the product under the earlier edition at Serial No. 93, with immediate effect, and provides for the relevant standard revisions to take effect from the date notified by BIS.
Accordingly, manufacturers should assess compliance against the current applicable standard, IS 9294:2023, rather than relying on the withdrawn edition.
The QCO also requires the applicable test certificate bearing the Standard Mark to accompany each covered consignment.
Important exemption: The QCO provides an export-related exception for qualifying steel products manufactured domestically for export according to another specification required by the foreign buyer. The applicability of this exemption must be assessed against the actual export arrangement and notification conditions.
4. Product Scope under IS 9294:2023
IS 9294:2023 covers cold-rolled stainless steel strips for the manufacture of razor blades.
The revised standard specifies one grade:
X66Cr13
The standard covers strips supplied in the following dimensional range:
| Parameter | Requirement |
|---|---|
| Grade | X66Cr13 |
| Thickness | 0.05 mm to 0.15 mm |
| Maximum width | Up to 25 mm |
| Product form | Cold-rolled stainless steel strips |
| Application | Razor blade manufacturing |
The dimensions and product characteristics must comply with the requirements of the current standard.
The manufacturer should identify the proposed thickness range and width before preparing the BIS application.
5. Technical Requirements under IS 9294:2023
The revised standard establishes specific technical requirements to ensure that the stainless steel strips are suitable for razor blade manufacturing.
The principal requirements include chemical composition, hardness, microstructure, carbide density, edge condition, dimensional accuracy and surface finish.
5.1 Chemical Composition
Chemical composition is one of the most important characteristics of stainless steel used for razor blades.
The standard specifies chemical composition requirements for grade X66Cr13.
The chemical parameters include:
- Carbon
- Silicon
- Manganese
- Chromium
- Sulphur
- Phosphorus
- Nickel
- Other specified residual or alloying elements, where applicable
The manufacturer must ensure that the chemical composition conforms to the applicable limits specified in IS 9294:2023.
Heat-wise chemical analysis and raw material traceability should be maintained.
5.2 Hardness Test
Hardness is an important property because razor blade strips must achieve the required hardness after the specified processing and heat-treatment operations.
IS 9294:2023 specifies hardness requirements and the corresponding test procedure.
The revised edition modified the recommended testing load and specified hardness values compared with the earlier edition.
The manufacturer should ensure that hardness testing is performed under the prescribed conditions.
5.3 Microstructure
Microstructure is important for evaluating the metallurgical quality of stainless steel strips.
The standard includes requirements for the microstructure of the material.
Microscopic examination helps assess the metallurgical structure and identify characteristics that may influence the material’s performance during razor blade manufacturing.
5.4 Carbide Density
Carbide density is an important metallurgical characteristic in razor blade steel.
The standard includes specific requirements for carbide density.
The 2023 revision modified the carbide density requirements, making it important for manufacturers to refer to the revised edition rather than older testing criteria.
5.5 Edge Condition
Edge condition is important because stainless steel strips are supplied in narrow widths and must be suitable for further processing.
The standard includes requirements relating to the edge condition of the strips.
The BIS product manual specifies inspection arrangements to ensure that slit edges are reasonably free from burrs.
5.6 Dimensions and Tolerances
The standard specifies dimensional requirements for cold-rolled stainless steel strips.
The main parameters include:
- Thickness
- Width
- Camber
- Applicable dimensional tolerances
The 2023 revision modified the dimensional and tolerance requirements.
Manufacturers should establish suitable measurement and inspection arrangements for all declared sizes.
5.7 Surface Finish
Surface finish is especially important for precision steel strips used in razor blade manufacturing.
The revised standard specifies surface roughness values for cold-rolled strips.
The manufacturer should maintain appropriate surface finishing and inspection controls to ensure conformity.
6. Testing Requirements for BIS Certification
Product testing is an essential part of the BIS certification process.
The BIS Product Manual PM/IS 9294/2, November 2023, identifies the following principal testing requirements.
| Test / Inspection | Purpose |
|---|---|
| Chemical composition | Verification of grade-wise chemical requirements |
| Hardness test | Verification of hardness |
| Microstructure | Assessment of metallurgical structure |
| Carbide density | Verification of carbide density requirements |
| Edge condition | Assessment of slit-edge quality |
| Thickness | Verification of strip thickness |
| Width | Verification of strip width |
| Camber | Assessment of dimensional conformity |
| Surface finish | Verification of surface roughness and finish |
6.1 Chemical Analysis
Chemical analysis verifies that the material conforms to the specified chemical composition for grade X66Cr13.
The BIS product manual identifies instrumental chemical analysis equipment, such as optical spectrometers or XRF equipment with the required channels.
It also lists alternative chemical analysis arrangements for individual elements.
The chemical parameters include carbon, silicon, manganese, chromium, sulphur, phosphorus, nickel, copper and molybdenum, as applicable.
6.2 Hardness Test
The hardness test evaluates the hardness of the cold-rolled stainless steel strips.
The product manual identifies a micro-hardness tester using the Vickers method.
The test must be carried out under the conditions prescribed in the current standard.
6.3 Microstructure Test
The microstructure test evaluates the metallurgical structure of the stainless steel.
The BIS product manual identifies an optical microscope with up to 1000x magnification and a camera for photographic documentation.
6.4 Carbide Density Test
Carbide density testing is required to verify the metallurgical characteristics specified by the standard.
The test should follow the applicable procedure and acceptance requirements under IS 9294:2023.
6.5 Dimensional Inspection
Dimensional inspection verifies thickness, width, camber and other applicable dimensional requirements.
The product manual identifies the following equipment:
- Vernier calipers
- Micrometer
- Steel scale
- Surface table
- Measuring tape
- Feeler gauge
- Straight edge
- Flat bench
6.6 Surface Finish Test
Surface finish testing evaluates the surface roughness of the cold-rolled strips.
The BIS product manual identifies a surface roughness tester calibrated with a standard roughness block.
6.7 Edge Condition Inspection
The strip edges should be inspected to ensure that they are reasonably free from burrs, as specified in the product manual.
Important: Exact chemical limits, hardness values, carbide density acceptance criteria, surface roughness limits and detailed test conditions must be verified from the full IS 9294:2023 standard. They should not be assumed from the earlier 1979 edition.
7. BIS Product Manual for IS 9294:2023
BIS published Product Manual PM/IS 9294/2, November 2023 for Cold-Rolled Stainless Steel Strips for Razor Blades.
The manual provides guidance on:
- Product scope
- Grade
- Sample size
- Grouping guidelines
- Testing equipment
- Scheme of Inspection and Testing
- Scope of licence
- Marking and test certificates
It is an important reference for manufacturers preparing for BIS certification.
7.1 Sample Size
The current BIS product manual specifies the following sample quantity:
| Testing purpose | Sample requirement |
|---|---|
| Product sample | 2 pieces |
| Length of each piece | 2.5 metres |
| Total sample length | 5 metres |
Therefore, the manufacturer should arrange two pieces of 2.5 metres each for the product certification sample, subject to the applicable BIS sampling instructions.
7.2 Grouping Guidelines
The BIS product manual provides grouping guidelines based on the thickness of stainless steel strips.
The product scope covers thicknesses from 0.05 mm to 0.15 mm and widths up to 25 mm.
For the purpose of Grant of Licence (GoL) and Change in Scope of Licence (CSoL), samples should be selected as follows:
- One sample of the lowest thickness.
- One sample of an intermediate thickness.
- One sample of the highest thickness.
The samples may be of any width within the proposed scope.
Testing these three thickness levels can support coverage of the complete proposed thickness range, subject to the grouping guidelines and the manufacturer’s manufacturing and testing facilities.
Important conditions:
- The manufacturer must have the necessary manufacturing and testing facilities for all sizes proposed in the licence.
- During licence operation, BIS may draw samples of all sizes covered in the licence on a rotational basis for independent testing.
- The final scope of licence depends on conformity assessment and the facilities available at the manufacturing unit.
8. Manufacturing and Quality Control Requirements
A manufacturer applying for BIS certification should demonstrate that its production process and quality-control system can consistently produce stainless steel strips conforming to IS 9294:2023.
The manufacturing process may involve:
- Procurement of stainless steel raw material.
- Incoming material inspection.
- Verification of chemical composition.
- Hot-rolled strip procurement or preparation.
- Cold rolling.
- Thickness and width control.
- Surface finishing.
- Slitting and edge preparation.
- Hardness testing.
- Microstructure and carbide density assessment.
- Surface finish inspection.
- Final dimensional inspection.
- Coil identification and packaging.
The actual manufacturing arrangement may differ depending on whether the applicant manufactures stainless steel from raw material or purchases hot-rolled strips for further cold rolling and processing.
The factory should maintain records covering:
- Raw material procurement
- Heat-wise chemical analysis
- Production process parameters
- Cold rolling records
- Thickness and width inspection
- Hardness test results
- Microstructure test reports
- Carbide density test records
- Surface finish records
- Edge condition inspection
- Calibration records
- Non-conforming product records
- Finished product traceability
9. BIS Scheme of Inspection and Testing
The BIS product manual includes a Scheme of Inspection and Testing (SIT) for IS 9294:2023.
Important requirements include the following.
9.1 Laboratory Requirements
The manufacturer must maintain a suitably equipped and staffed laboratory for the tests specified in the standard.
The product manual identifies equipment for:
- Chemical analysis
- Dimensional inspection
- Microstructure examination
- Hardness testing
- Surface roughness testing
- Sample preparation
9.2 Control Unit
The product manual defines the control unit as:
Strips cold rolled from the same hot-rolled strip and having the same thickness.
This definition is important for establishing production and testing records.
9.3 Levels of Control
The product manual specifies the following recommended testing frequencies:
| Test | Recommended frequency |
|---|---|
| Freedom from defects | Adequate in-process control |
| Chemical composition – Ladle analysis | One sample from each heat, where applicable |
| Chemical composition – Product analysis | One sample from each cast, where applicable |
| Hardness test | One sample from each control unit |
| Microstructure | One sample from each control unit |
| Carbide density | One sample from each control unit |
| Edge condition | Adequate inspection of each strip |
| Dimensions and tolerances | Adequate inspection of each strip |
| Surface finish | One sample from each control unit |
The manual makes specific distinctions between stainless steel manufacturers and re-rollers.
For example, chemical analysis requirements depend on whether the manufacturer has stainless steelmaking facilities or obtains material from an external supplier.
If material is already ISI-marked and received with the appropriate test certificate, the manual specifies circumstances where further testing is not required.
9.4 Subcontracting of Tests
The product manual states that subcontracting is permitted for specified tests to laboratories recognised by BIS or government laboratories empanelled by BIS, subject to the applicable requirements.
The decision on whether testing equipment must be maintained in-house or subcontracting is permitted is determined by BIS.
9.5 Test Certificate
For each consignment of BIS-certified material conforming to IS 9294:2023, the product manual requires a test certificate containing:
- Standard Mark
- Cast or control unit number
- Chemical composition results
- Mechanical properties
- Dimensions and tolerances
- Microstructure and carbide density results
- Surface finish results
The test certificate should provide traceability between the finished material and the relevant production and inspection records.
10. Marking and Packaging Requirements
The BIS product manual specifies marking requirements for the product.
The Standard Mark and licence number must be incorporated on:
- The top of each coil
- Each package of sheets
- A tag attached to each coil or packet
- The applicable test certificate
The marking or label must also include the prescribed phrase:
“Please see www.bis.gov.in for BIS certification details”.
The manufacturer must follow the marking requirements prescribed in the licence schedule and the applicable BIS regulations.
The Standard Mark must not be used on products that do not conform to the standard or are outside the approved licence scope.
11. Documents Required for BIS Certification
The following documents are generally relevant when preparing a BIS application for Cold-Rolled Stainless Steel Strips for Razor Blades.
A. Company Documents
- Company registration certificate or constitution documents
- GST registration certificate
- PAN card
- Factory address proof
- Authorised signatory details
- Identity and address proof of authorised signatory
- Factory layout plan
- Details of manufacturing premises
B. Manufacturing Documents
- Manufacturing process flow chart
- List of manufacturing machinery
- Cold rolling mill details
- Slitting machine details
- Production capacity details
- Product specifications
- Grade details – X66Cr13
- Thickness and width range
- Raw material specifications
- Process control procedures
C. Quality Control and Testing Documents
- Quality control plan
- Inspection and testing plan
- In-house laboratory equipment list
- Calibration certificates
- Chemical analysis reports
- Hardness test reports
- Microstructure test reports
- Carbide density test reports
- Thickness and width inspection records
- Surface roughness test records
- Edge condition inspection records
- Finished product inspection records
- Non-conformity and corrective action procedures
D. BIS Application Documents
- BIS application and supporting information
- Product description and proposed scope
- Trademark or brand authorisation documents, where applicable
- Factory and laboratory details
- Applicable declarations and undertakings
- Relevant fee payment details
Additional documents may be required depending on the manufacturing arrangement and proposed product scope.
12. BIS Certification Process for Razor Blade Steel Strips
The certification process generally involves the following stages.
Step 1: Product and Standard Verification
Confirm that the product falls within the scope of IS 9294:2023.
Identify grade X66Cr13 and the proposed thickness and width range.
Step 2: Factory and Laboratory Assessment
Review the manufacturing facility, cold rolling machinery, slitting arrangements, laboratory equipment and quality-control system.
Step 3: Preparation of BIS Application
Prepare the required company, manufacturing, product and quality-control documents.
The proposed scope should clearly identify the grade, thickness and width range.
Step 4: Sample Selection
Samples should be selected in accordance with the BIS product manual.
The current manual specifies two pieces of 2.5 metres each. For grouping across thickness ranges, samples of the lowest, intermediate and highest thickness are required.
Step 5: Product Testing
Arrange testing against the applicable requirements of IS 9294:2023.
The main tests include:
- Chemical composition
- Hardness
- Microstructure
- Carbide density
- Edge condition
- Dimensions and tolerances
- Surface finish
Step 6: BIS Factory Inspection
BIS may conduct a factory inspection to assess:
- Manufacturing facilities
- Cold rolling process
- Slitting and finishing arrangements
- Testing infrastructure
- Quality-control procedures
- Raw material records
- Production and inspection records
- Sample selection and testing
- Marking and packaging arrangements
Step 7: Grant of BIS Licence
After satisfactory assessment of the application, factory facilities and product conformity, BIS may grant a licence to use the ISI Standard Mark.
Step 8: Post-Licence Compliance
After licence grant, the manufacturer must maintain continuous conformity through:
- Routine testing
- Control unit-wise production records
- Chemical analysis
- Hardness testing
- Microstructure and carbide density testing
- Dimensional inspection
- Surface finish control
- Calibration of testing equipment
- Product traceability
- BIS surveillance compliance
13. BIS Certification Cost for Stainless Steel Razor Blade Strips
The total cost of BIS certification depends on the manufacturing facility, product scope, testing arrangements and applicable BIS fee structure.
Potential cost components include:
- BIS application fee
- BIS licence fee
- Annual marking fee
- Product testing charges
- Sample preparation and transportation
- Laboratory charges
- Inspection-related expenses
- Consultancy and documentation charges, where professional assistance is engaged
Annual Marking Fee Reference
The BIS Scheme-I marking fee schedule published in January 2026 lists the following annual minimum marking fees for IS 9294:
| Unit category | Annual minimum marking fee |
|---|---|
| Large | ₹92,000 |
| Medium | ₹74,000 |
| Small | ₹46,000 |
| Micro | ₹18,400 |
The published schedule also specifies a unit rate of ₹30 per metric tonne.
These are marking fee references from the published BIS schedule and should not be confused with the total certification cost. Other applicable fees and charges are separate.
A manufacturer should obtain a project-specific estimate after reviewing the product scope, factory infrastructure and laboratory requirements.
14. Common Challenges in BIS Certification
Manufacturers may encounter the following challenges during certification:
1. Applying under the withdrawn standard: Applications should be prepared using IS 9294:2023 rather than the withdrawn 1979 edition.
2. Incorrect grade identification: The current standard covers grade X66Cr13. The declared product must conform to this grade.
3. Chemical composition failures: The material may fail to meet the specified chemical composition requirements.
4. Hardness non-conformity: Improper processing or heat treatment may affect the required hardness.
5. Microstructure failures: Metallurgical characteristics may not conform to the requirements of the standard.
6. Carbide density issues: The material may fail to meet the revised carbide density requirements.
7. Dimensional variation: Thickness, width or camber may fall outside the specified tolerances.
8. Surface finish problems: Inadequate rolling or finishing control may result in unacceptable surface roughness.
9. Inadequate testing infrastructure: The factory may not have suitable equipment for hardness, microstructure, carbide density and surface finish testing.
10. Incorrect sample grouping: The manufacturer must plan sample selection across the lowest, intermediate and highest thickness levels.
A preliminary factory and documentation assessment can help identify these issues before the formal BIS application.
15. Why Choose Qualitance India for BIS Certification?
Qualitance India provides professional consultancy and regulatory compliance support for manufacturers seeking BIS product certification in India.
For Cold-Rolled Stainless Steel Strips for Razor Blades under IS 9294:2023, our support can include:
- Product and Indian Standard applicability review
- BIS certification feasibility assessment
- Grade and product scope review
- Thickness and width grouping assessment
- Manufacturing process assessment
- Quality-control documentation
- Laboratory and product testing coordination
- BIS application preparation
- Factory inspection preparation
- Assistance in addressing non-conformities
- Post-licence compliance guidance
Our objective is to help manufacturers understand the applicable regulatory requirements and establish a practical certification process.
Qualitance India – Improving Quality & Competence
Website: https://qualitanceindia.com
Email: info@qualitanceindia.com
Phone / WhatsApp: +91 93106 15170
16. Frequently Asked Questions (FAQs)
Q1. Which Indian Standard applies to Cold-Rolled Stainless Steel Strips for Razor Blades?
The current standard is IS 9294:2023 – Cold-Rolled Stainless Steel Strips for Razor Blades.
Q2. Is IS 9294:1979 still valid?
No. IS 9294:1979 was withdrawn on 3 February 2024 and replaced by IS 9294:2023.
Q3. Is BIS certification mandatory for stainless steel strips for razor blades?
Yes. The product is covered under the Steel and Steel Products Quality Control Order framework. Manufacturers must comply with the applicable current standard and QCO provisions.
Q4. Which grade is covered under IS 9294:2023?
The revised standard covers grade X66Cr13.
Q5. What is the thickness range under IS 9294:2023?
The standard covers strip thicknesses from 0.05 mm to 0.15 mm.
Q6. What is the maximum strip width?
The product manual identifies widths up to 25 mm.
Q7. What is the sample size under the current BIS product manual?
The product manual specifies two pieces of 2.5 metres length each.
Q8. What are the grouping guidelines under IS 9294:2023?
Samples of the lowest, intermediate and highest thicknesses are drawn and tested to cover the proposed thickness range, subject to the manufacturer’s manufacturing and testing facilities.
Q9. What tests are required for BIS certification?
The principal tests include chemical composition, hardness, microstructure, carbide density, edge condition, dimensions and tolerances, and surface finish.
Q10. What is the control unit under the BIS product manual?
Strips cold rolled from the same hot-rolled strip and having the same thickness constitute a control unit.
Q11. Can a foreign manufacturer obtain BIS certification for IS 9294:2023?
Foreign manufacturers can apply under the applicable BIS Foreign Manufacturers Certification Scheme, subject to the relevant requirements.
Q12. What is the annual BIS marking fee for IS 9294?
The January 2026 BIS marking fee schedule lists annual minimum fees of ₹92,000 for large units, ₹74,000 for medium units, ₹46,000 for small units and ₹18,400 for micro units. Applicable production-based marking charges and other fees must also be considered.
17. Conclusion
Cold-Rolled Stainless Steel Strips for Razor Blades are specialised materials that require precise control over chemical composition, hardness, microstructure, carbide density, dimensions and surface finish.
IS 9294:2023 replaced the earlier IS 9294:1979 edition and introduced important changes to hardness testing, carbide density, sampling, dimensional tolerances and surface finish requirements.
The BIS Product Manual PM/IS 9294/2, November 2023, provides practical guidance on sample size, grouping, testing equipment, inspection frequency, control units and marking requirements.
Manufacturers must ensure that their product conforms to the current standard and that their manufacturing and testing infrastructure is suitable for BIS certification.
Proper standard selection, sample planning, metallurgical testing and documentation are essential for obtaining and maintaining the BIS licence.
Need assistance with BIS Certification for Cold-Rolled Stainless Steel Strips for Razor Blades?
Contact Qualitance India for professional guidance on product applicability, BIS application preparation, sample testing, factory readiness and certification support.
Qualitance India – Improving Quality & Competence
Official References and Further Reading
- BIS Product Manual PM/IS 9294/2, November 2023: https://www.bis.gov.in/wp-content/uploads/2023/11/Revised-PM-IS-9294-2023-Final.pdf
- BIS Circular CMD-2/16:9294, dated 22 November 2023 – Implementation Guidelines for Revised IS 9294:2023: https://www.services.bis.gov.in/tmp/Circular_jiym_2023-11-22.pdf
- Steel and Steel Products (Quality Control) Order, 2024: S.O. 3716(E), dated 29 August 2024.
- BIS Product Manuals: https://www.bis.gov.in/product-certification/product-specific-information-2/product-manuals/
- BIS Laboratory Information Management System: https://lims.bis.gov.in/
- BIS Marking Fee Schedule for Scheme-I Products: https://www.bis.gov.in/wp-content/uploads/2026/01/Marking-fee-for-all-products-under-certification-scheme-1.pdf
- BIS Products under Compulsory Certification: https://www.bis.gov.in/product-certification/products-under-compulsory-certification/
Need help with BIS certification for this product?
Get a free consultation from our compliance experts — we handle testing, documentation and the complete BIS process for you.
BIS Certification Readiness Checklist 2026
- Documents, testing & factory requirements in one place
- Covers ISI Mark, CRS, FMCS & Hallmarking
- Tick-box format — share it with your team